Speed Sensor - Replace
`
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
[SENR1935]
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Proportional Reducing Valve - Calibrate
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Controller Input and Output Values
ELECTRICAL AND STARTING SYSTEM
SENSOR GP
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Sensors
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Speed Sensor - Replace
Show/hide table
![]() | |
Illustration 1 | g00667337 |
Installation of the speed sensor (1) Speed Sensor (2) Locknut (3) Magnetic Core (4) Gear (5) Flywheel Housing |
Prior to replacement of the sensor, ensure that the sensor has failed. Always check that the power is available to the sensor. Measure the voltage between the contacts of the sensor. Check for metal shavings on the magnetic tip or the gear teeth.
Perform the following procedure in order to replace the speed sensor.
- Turn the key start switch and the disconnect switch to the OFF position.
- Slowly tighten speed sensor (1) into flywheel housing (5) until magnetic core (3) contacts gear (4) .
- Turn speed sensor (1) counterclockwise. The turn should be approximately 3/4 of a rotation.
- Temporarily tighten locknut (2) .
- Set the engine speed dial at position 1 (LOW IDLE position).
- Turn the disconnect switch to the ON position.
- Start the engine.
- Activate the service mode.
- Enter service code 12 in order to display the engine speed.
- Verify that 800 RPM is displayed. AGS, ALB and APB the engine rpm should be 880 rpm.
- If the correct rpm is not displayed, turn speed sensor (1) clockwise. The turn should not be greater than 1/3 of a rotation.
- Stop the engine.
- Tighten locknut (2) to a torque of 25 N·m (18.4 lb ft).
- Verify that the sensor corrects the problem.
- Clear the error log. Refer to Testing and Adjusting, "Using Service Mode".
Information System:
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Proportional Reducing Valve - Calibrate
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Proportional Reducing Valve Sweep - Test
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Electronic Governor - Calibrate
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Digital Output On/Off - Test
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Engine Speed Dial Setting - Check
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Hydraulic Hammer - Adjust
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Parameter - Adjust
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Troubleshooting Undiagnosed Problems
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Real Time Error Codes
305 CR Mini Hydraulic Excavator
Cooling System Coolant (ELC) - Change
Horizontal Pin Lock Series PW Quick Coupler
Rated Load
345B Series II Excavator Hydraulic System
Main Control Valve
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Controller Input and Output Values
325C Excavator Machine System Specifications
Boom - 5550 mm (218.5 inch)
3500B, 776D, 777D, 784C, 785C, 789C, 793C and and 793D Off-Highway Truck/Tractors
Refrigerant Compressor
305 CR Mini Hydraulic Excavator
Engine Air Filter Primary Element - Clean/Replace
325C Excavator Machine System Specifications
Boom - 6150 mm (242.1 inch)
305 CR Mini Hydraulic Excavator
Engine Oil Level - Check
M315 Excavator Hydraulic System
Engine Performance - Test
CS44 and CP44 Soil Compactor Machine System
Vibratory Support
M315 Excavator Hydraulic System
Engine Speed - Test and Adjust - No Load
305 CR Mini Hydraulic Excavator
Engine Oil and Filter - Change
315C Excavator
Engine Speed Control
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2
Check of Governor Actuator - Troubleshoot - CID 91 - 315C, 318C, 319C, 320C, 321C, And 322C