Position the Valve Mechanism Before Maintenance Procedures
`
C7.1 Industrial Engine
[UENR0666]
C7.1 Industrial Engine
Engine Valve Lash - Inspect
C7.1 Industrial Engine
Exhaust Cooler (NRS) - Test
Show/hide table
| NOTICE |
|---|
Ensure that this procedure is carried out before the rocker shaft is removed. |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A (1) | 9U-6198 | Crankshaft Turning Tool | 1 |
| A (2) | 5P-7306 | Housing | 1 |
| 5P-7305 | Engine Turning Tool | 1 | |
| B | 8T-5096 | Dial Indicator | 1 |
| - | Magnetic Base and Stand | 1 | |
Show/hide table
| ( 1 ) | The Crankshaft Turning Tool is used on the front pulley. |
| ( 2 ) | This Tool is used in the aperture for the electric starting motor. |
Show/hide table
 | |
| Illustration 1 | g01334425 |
Cylinder and valve location (A) Exhaust valve (B) Inlet valve | |
- Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.
- Remove the glow plugs. Refer to Disassembly and Assembly, "Glow Plugs - Remove and Install" for the correct procedure.
- Select an accessible exhaust rocker arm. The exhaust rocker arm can be on any cylinder.
- Use Tooling (A) to rotate the crankshaft until the push rod end of the selected exhaust rocker arm (1) reaches the lowest position. This position indicates that the hydraulic lifter is sitting on the base circle of the camshaft lobe.
- Mount Tooling (B) with the pointer that is touching the top face of the exhaust rocker arm (1) above the push rod.
Show/hide table
 | |
| Illustration 2 | g02313413 |
Typical example One electronic unit injector is not shown for clarity. | |
- Use Tooling (A) to rotate the crankshaft until the hydraulic lifter starts to open the exhaust valve. Continue to rotate the crankshaft until the finger of the indicator moves by 2.8 mm (0.11 inch).
Note: This measurement indicates the safe position of 60 degrees. The precise position will vary depending whether the hydraulic lifter is leaked down or not. The reading on the dial indicator may reduce as the hydraulic lifter continues to leak down. As soon as a value of 2.8 mm (0.11 inch) is reached the crankshaft is in a safe position.
Note: Make temporary marks on the vibration damper and the front housing once the engine is in the safe position.
Show/hide table
| NOTICE |
|---|
Ensure that the crankshaft is located in the safe position before the rocker shaft assembly is installed. |
Information System:
C6.6 Industrial Engine
Fuel Injection Pump Gear - Remove
C6.6 Industrial Engine
Fuel Injection Pump - Install
C6.6 Industrial Engine
Fuel Injection Pump - Remove
C6.6 Industrial Engine
Inlet Air Control - Install - NRS Inlet Air Mixer
C6.6 Industrial Engine
Inlet Air Control - Remove - NRS Inlet Air Mixer
C6.6 Industrial Engine
Fuel Injection Lines - Install
C6.6 Industrial Engine
Fuel Injection Lines - Remove
C6.6 Industrial Engine
Fuel Manifold (Rail) - Remove and Install
C6.6 Industrial Engine
Fuel Filter Base - Remove and Install - Single Secondary Fuel Filter
C6.6 Industrial Engine
Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
374F Excavator Machine System
Grease Lines
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Fuel Transfer and Priming Pump - Remove and Install
C4.4 Industrial Engine
Position the Valve Mechanism Before Maintenance Procedures
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Fuel Shutoff Solenoid - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Engine Oil Filter and Oil Filter Base - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Fan - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Engine Oil Cooler - Remove and Install
303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement
Hood - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Refrigerant Condenser - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Water Temperature Regulator - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Refrigerant Compressor - Remove and Install
2010/05/17
The Relay Switch for the Heater has been Relocated to Improve the Reliability of the Switch on Certain Excavators {1417}
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Refrigerant Receiver-Dryer - Remove and Install
349E Excavator Hydraulic System
Gear Pump (Pilot) - Test