Work Tool Parameter - Default Values - System 18
`
336D MHPU Mobile Hydraulic Power Unit Hydraulic System
[UENR0857]
HYDRAULIC SYSTEM
320D, 320D2, 321D, 323D, 324D, 325D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators Tool Control System
Solenoid Valve (Proportional Reducing) - Calibrate
320D, 320D2, 321D, 323D, 324D, 325D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators Tool Control System
Work Tool - Select
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Machine Tool Control System - Select
320D, 320D2, 321D, 323D, 324D, 325D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators Tool Control System
Work Tool Parameter - Program
320D, 320D2, 321D, 323D, 324D, 325D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators Tool Control System
Process for Setting Up the Work Tool
320D, 320D2, 321D, 323D, 324D, 325D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators Tool Control System
Solenoid Valve (Proportional Reducing) - Calibrate - Number 1 Relief Valve and Number 2 Relief Valve
320D, 320D2, 321D, 323D, 324D, 325D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators Tool Control System
Solenoid Valve (Proportional Reducing) - Calibrate - Negative Flow Control
Note: For this system, parameters that are not shown in the tables do not affect operation of the work tool.
Note: The parameters in the "DARK GRAY" cells do not affect the operation of the work tool.
Table 1 shows some of the approved AVSpare work tools that are used.
Table 2 shows parameters for "TOOL#1" through "TOOL#5".
Table 3 shows parameters for "TOOL#6" through "TOOL#10".
Note: Refer to the specific machine model for additional parameters.
Show/hide table
| SYSTEM 18 | ||
| Work Tool | Direction of Flow | System 18 "TOOL#s" |
| "Hammers" | 1 Way | "TOOL#1", "TOOL#2", "TOOL#3" |
| "Multi-Processor" | 2 Way | "TOOL#4" |
| "Shear" | 2 Way | "TOOL#5", "TOOL#6" |
| "Grapple" | 2 Way | "TOOL#7" |
Show/hide table
| Name | Display | "TOOL#1" | "TOOL#2" | "TOOL#3" | "TOOL#4" | "TOOL#5" |
|---|---|---|---|---|---|---|
| "TOOL PROGRAM -> GENERAL" | ||||||
| Name of the tool | "NAME" | H120CS | H130S | H140DS | MP20 | S320 |
| Maximum position of the dial for the throttle | "MAX DIAL" | 10 | 10 | 10 | 10 | 10 |
| Minimum position of the dial for the throttle | "MIN DIAL" | 1 | 1 | 1 | 1 | 1 |
| Dial for the control of the flow | "DIAL FLOW CONT" | ON | ON | ON | ON | ON |
| Control for the underspeed option | "UNDER SPEED ENABLE" | ENABLED | ENABLED | ENABLED | ENABLED | ENABLED |
| Temperature of the high temperature warning for the hydraulic oil | "WARNING HYD TEMP" | 80 | 80 | 80 | 100 | 100 |
| Combiner for two pump flow | "COMBINER ENABLE" | "DISABLE" | "ENABLED" | "ENABLED" | "ENABLED" | "DISABLE" |
| Initial power reduction of the main pump | "INT PUMP POWER RE" | 5.0 | 5.0 | 5.0 | 5.0 | 5.0 |
| Total power reduction of the main pump | "TOTAL PUMP POWER RE" | 50.0 | 50.0 | 50.0 | 50.0 | 50.0 |
| One-way flow or two-way flow | "ONE OR TWO WAY" | "ONE-WAY" | "ONE-WAY" | "ONE-WAY" | "TWO-WAY" | "TWO-WAY" |
| Pressure of the number 1 variable relief valve | "VAR RELIEF #1 PRES" | 21000 | 21000 | 21000 | 40000 | 40000 |
| Pressure of the number 2 variable relief valve | "VAR RELIEF #2 PRES" | 21000 | 21000 | 21000 | 40000 | 40000 |
| Maximum pressure of the derate of the F2 valve | "F2 DERATE MAX PRES" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Starting pressure of the F2 valve for squeeze | "F2 SQEZ START PRES" | 40000 | 40000 | 40000 | 40000 | 40000 |
| Ending pressure of the F2 valve for squeeze | "F2 SQEZ END PRES" | 40000 | 40000 | 40000 | 40000 | 40000 |
| Maximum pilot pressure for the extension of attachment valve during multiple operations | "F2 MULTI OPE EXTND" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Maximum pilot pressure for the retraction of the attachment valve during multiple operations | "F2 MULTI OPE RETCT" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Maximum pilot pressure for the extension of auxiliary valve during multiple operations | "f2 MULTI OPE EXTND" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Maximum pilot pressure for the retraction of the auxiliary valve during multiple operations | "f2 MULTI OPE RETCT" | 4000 | 4000 | 4000 | 4000 | 4000 |
| "TOOL PROGRAM -> CONTROL MODES" | ||||||
| Control mode of the number 1 switch on the right joystick | "MOD R JOYSTK SW #1" | "NO CONTROL" | "NO CONTROL" | "MOM VALVE #1 EXT" | "NO CONTROL" | |
| Control mode of the thumb wheel on the left joystick | "MOD L THUMB WHEEL" | "VALVE #3 REVERSE" | "VALVE #3 REVERSE" | "NO CONTROL" | "NO CONTROL" | |
| Control mode of the thumb wheel on the right joystick | "MOD R THUMB WHEEL" | "VALVE #1 REVERSE" | "VALVE #1 REVERSE" | "NO CONTROL" | "VALVE #1 REVERSE" | |
| "TOOL PROGRAM -> ATTACHMENT #1 VALVE" | ||||||
| Flow settings of the number 1 attachment valve | "A1 FLOW" | 150 | 190 | 200 | 200 | 150 |
| Additional flow for the number 1 attachment valve during multiple operation | "A1 MULTI ADD FLOW" | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 |
| Normal working pressure of the number 1 attachment valve | "A1 NOMINAL PRES" | 16000 | 16000 | 16000 | 8000 | 8000 |
| Open time of the number 1 attachment valve | "A1 OPEN TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Close time of the number 1 attachment valve | "A1 CLOSE TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Maximum pressure for the extension of the number 1 attachment valve | "A1 EXTND MAX PRES" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Maximum pressure for the retraction of the number 1 attachment valve | "A1 RETCT MAX PRES" | N/A 0 |
N/A 0 |
N/A 0 |
4000 | 4000 |
| Direction of the oil flow for the number 1 attachment valve | "A1 FLOW DIRCTN" | N/A Normal |
N/A Normal |
N/A Normal |
Normal | Normal |
| "TOOL PROGRAM -> ATTACHMENT #2 VALVE" | ||||||
| Flow settings of the number 2 attachment valve | "A2 FLOW" | N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
| Additional flow for the number 2 attachment valve during multiple operation | "A2 MULTI ADD FLOW" | N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
| Normal working pressure of the number 2 attachment valve | "A2 NOMINAL PRES" | N/A 40000 |
N/A 40000 |
N/A 40000 |
N/A 40000 |
N/A 40000 |
| Open time of the number 2 attachment valve | "A2 OPEN TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Close time of the number 2 attachment valve | "A2 CLOSE TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Maximum pressure for the extension of the number 2 attachment valve | "A2 EXTND MAX PRES" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Maximum pressure for the retraction of the number 2 attachment valve | "A2 RETCT MAX PRES" | N/A 0 |
N/A 0 |
N/A 0 |
4000 | 4000 |
| Direction of the oil flow for the number 2 attachment valve | "A2 FLOW DIRCTN" | Normal N/A |
Normal N/A |
Normal N/A |
Normal | Normal |
| "TOOL PROGRAM -> ATTACHMENT #3 VALVE" | ||||||
| Flow settings of the number 3 attachment valve | "A3 FLOW" | N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
| Additional flow for the number 3 attachment valve during multiple operation | "A3 MULTI ADD FLOW" | N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
| Normal working pressure of the number 3 attachment valve | "A3 NOMINAL PRES" | N/A 40000 |
N/A 40000 |
N/A 40000 |
N/A 40000 |
N/A 40000 |
| Open time of the number 3 attachment valve | "A3 OPEN TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Close time of the number 3 attachment valve | "A3 CLOSE TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Maximum pressure for the extension of the number 3 attachment valve | "A3 EXTND MAX PRES" | 1400 | 1400 | 1400 | 1400 | 1400 |
| Maximum pressure for the retraction of the number 3 attachment valve | "A3 RETCT MAX PRES" | 1400 | 1400 | 1400 | 1400 | 1400 |
| Direction of the oil flow for the number 3 attachment valve | "A3 FLOW DIRCTN" | Normal | Normal | Normal | Normal | Normal |
Show/hide table
| Name | Display | "TOOL#6" | "TOOL#7" | "TOOL#8" | "TOOL#9" | "TOOL#10" |
|---|---|---|---|---|---|---|
| "TOOL PROGRAM -> GENERAL" | ||||||
| Name of the tool | "NAME" | S340 | G320B | DCT Bucket | 0 | 0 |
| Maximum position of the dial for the throttle | "MAX DIAL" | 10 | 10 | 10 | 10 | 10 |
| Minimum position of the dial for the throttle | "MIN DIAL" | 1 | 1 | 1 | 1 | 1 |
| Dial for the control of the flow | "DIAL FLOW CONT" | ON | ON | ON | ON | ON |
| Control for the underspeed option | "UNDER SPEED ENABLE" | ENABLED | ENABLED | ENABLED | ENABLED | ENABLED |
| Temperature of the high temperature warning for the hydraulic oil | "WARNING HYD TEMP" | 100 | 100 | 100 | 126 | 126 |
| Combiner for two pump flow | "COMBINER ENABLE" | "ENABLED" | "DISABLE" | "DISABLE" | "DISABLE" | "DISABLE" |
| Initial power reduction of the main pump | "INT PUMP POWER RE" | 5.0 | 5.0 | 5.0 | 5.0 | 5.0 |
| Total power reduction of the main pump | "TOTAL PUMP POWER RE" | 50.0 | 50.0 | 50.0 | 50.0 | 50.0 |
| One-way flow or two-way flow | "ONE OR TWO WAY" | "TWO-WAY" | "TWO-WAY" | "TWO-WAY" | "TWO-WAY" | "TWO-WAY" |
| Pressure of the number 1 variable relief valve | "VAR RELIEF #1 PRES" | 40000 | 40000 | 40000 | 40000 | 40000 |
| Pressure of the number 2 variable relief valve | "VAR RELIEF #2 PRES" | 40000 | 40000 | 40000 | 40000 | 40000 |
| Maximum pressure of the derate of the F2 valve | "F2 DERATE MAX PRES" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Starting pressure of the F2 valve for squeeze | "F2 SQEZ START PRES" | 40000 | 40000 | 40000 | 40000 | 40000 |
| Ending pressure of the F2 valve for squeeze | "F2 SQEZ END PRES" | 40000 | 40000 | 40000 | 40000 | 40000 |
| Maximum pilot pressure for the extension of attachment valve during multiple operations | "F2 MULTI OPE EXTND" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Maximum pilot pressure for the retraction of the attachment valve during multiple operations | "F2 MULTI OPE RETCT" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Maximum pilot pressure for the extension of auxiliary valve during multiple operations | "f2 MULTI OPE EXTND" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Maximum pilot pressure for the retraction of the auxiliary valve during multiple operations | "f2 MULTI OPE RETCT" | 4000 | 4000 | 4000 | 4000 | 4000 |
| "TOOL PROGRAM -> CONTROL MODES" | ||||||
| Control mode of the number 1 switch on the right joystick | "MOD R JOYSTK SW #1" | "NO CONTROL" | "NO CONTROL" | "MOM VALVE #1 EXT" | "NO CONTROL" | |
| Control mode of the thumb wheel on the left joystick | "MOD L THUMB WHEEL" | "VALVE #3 REVERSE" | "VALVE #3 REVERSE" | "NO CONTROL" | "NO CONTROL" | |
| Control mode of the thumb wheel on the right joystick | "MOD R THUMB WHEEL" | "VALVE #1 REVERSE" | "VALVE #1 REVERSE" | "NO CONTROL" | "VALVE #1 REVERSE" | |
| "TOOL PROGRAM -> ATTACHMENT #1 VALVE" | ||||||
| Flow settings of the number 1 attachment valve | "A1 FLOW" | 300 | 120 | 50 | 0.0 | 0.0 |
| Additional flow for the number 1 attachment valve during multiple operation | "A1 MULTI ADD FLOW" | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 |
| Normal working pressure of the number 1 attachment valve | "A1 NOMINAL PRES" | 8000 | 8000 | 8000 | 40000 | 40000 |
| Open time of the number 1 attachment valve | "A1 OPEN TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Close time of the number 1 attachment valve | "A1 CLOSE TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Maximum pressure for the extension of the number 1 attachment valve | "A1 EXTND MAX PRES" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Maximum pressure for the retraction of the number 1 attachment valve | "A1 RETCT MAX PRES" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Direction of the oil flow for the number 1 attachment valve | "A1 FLOW DIRCTN" | Normal | Normal | Normal | Normal | Normal |
| "TOOL PROGRAM -> ATTACHMENT #2 VALVE" | ||||||
| Flow settings of the number 2 attachment valve | "A2 FLOW" | N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
| Additional flow for the number 2 attachment valve during multiple operation | "A2 MULTI ADD FLOW" | N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
| Normal working pressure of the number 2 attachment valve | "A2 NOMINAL PRES" | N/A 40000 |
N/A 40000 |
N/A 40000 |
N/A 40000 |
N/A 40000 |
| Open time of the number 2 attachment valve | "A2 OPEN TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Close time of the number 2 attachment valve | "A2 CLOSE TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Maximum pressure for the extension of the number 2 attachment valve | "A2 EXTND MAX PRES" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Maximum pressure for the retraction of the number 2 attachment valve | "A2 RETCT MAX PRES" | 4000 | 4000 | 4000 | 4000 | 4000 |
| Direction of the oil flow for the number 2 attachment valve | "A2 FLOW DIRCTN" | Normal | Normal | Normal | Normal | Normal |
| "TOOL PROGRAM -> ATTACHMENT #3 VALVE" | ||||||
| Flow settings of the number 3 attachment valve | "A3 FLOW" | N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
| Additional flow for the number 3 attachment valve during multiple operation | "A3 MULTI ADD FLOW" | N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
N/A 0 |
| Normal working pressure of the number 3 attachment valve | "A3 NOMINAL PRES" | N/A 40000 |
N/A 40000 |
N/A 40000 |
N/A 40000 |
N/A 40000 |
| Open time of the number 3 attachment valve | "A3 OPEN TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Close time of the number 3 attachment valve | "A3 CLOSE TIME" | 0.2 | 0.2 | 0.2 | 0.2 | 0.2 |
| Maximum pressure for the extension of the number 3 attachment valve | "A3 EXTND MAX PRES" | 1400 | 1400 | 1400 | 1400 | 1400 |
| Maximum pressure for the retraction of the number 3 attachment valve | "A3 RETCT MAX PRES" | 1400 | 1400 | 1400 | 1400 | 1400 |
| Direction of the oil flow for the number 3 attachment valve | "A3 FLOW DIRCTN" | Normal | Normal | Normal | Normal | Normal |
Information System:
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Upper Frame and Undercarriage Frame - Connect
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Upper Frame and Undercarriage Frame - Separate
324E Excavator
Additional Messages
C4.4 Industrial Engine
Air Inlet and Exhaust System - Single Turbocharger
324E Excavator
Safety Messages
C6.6 Industrial Engine
Air Compressor - Remove and Install - Single Cylinder
C6.6 Industrial Engine
Air Compressor - Remove and Install - Twin Cylinder Compressor
C6.6 Industrial Engine
Alternator - Install
C6.6 Industrial Engine
Electric Starting Motor - Remove and Install
C6.6 Industrial Engine
Alternator - Remove
C6.6 Industrial Engine
ECM Mounting Bracket - Remove and Install
C6.6 Industrial Engine
Electronic Control Module - Remove and Install - Electronic Control Module With Quick Coupler Connections
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Work Tool Parameter - Default Values - Medium Pressure
336D MHPU Mobile Hydraulic Power Unit Hydraulic System
Relief Valve (Auxiliary) - Test and Adjust - Line, System 18
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Relief Valve (Medium Pressure Function) - Test and Adjust - Main
C9.3 Engines for Caterpillar Built Machines
Exhaust Sensor Lines - Remove and Install
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Counterweight - Remove and Install
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Hydraulic Tank - Remove
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Hydraulic Tank - Install
349F and 352F Excavators Hydraulic System
Check Valve (Return Makeup) - Slow Return Check Valve
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Load Control Valve (Boom Cylinder) - Remove and Install
C9.3 Tier 4 Final Engines
Fuel Filter Base - Primary
Installation Procedure for the 260-8007 Front Lines Group {5057}
324E Excavator
Specifications