Finding Top Center Position for No. 1 Piston
`
C4.4 Industrial Engine
[KENR9119]
C4.4 Industrial Engine
Connecting Rod - Inspect
C4.4 Industrial Engine
Fuel Injection Timing - Check
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A(1) | 9U-6198 | Crankshaft Turning Tool | 1 |
| A(2) | 5P-7306 | Housing | 1 |
| 5P-7305 | Engine Turning Tool | 1 | |
| B | 230-6284 | Timing Pin (Camshaft) | 1 |
| C | 136-4632 | Timing Pin (Crankshaft) | 1 |
Show/hide table
| (1) | The Crankshaft Turning Tool is used on the front pulley. |
| (2) | This Tool is used in the aperture for the electric starting motor. |
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
- Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install".
Show/hide table
Illustration 1 g01907734 Typical example Show/hide table
Illustration 2 g01907735 Typical example - Use Tooling (A) in order to rotate the crankshaft until the Hole (X) in the camshaft gear (1) aligns with the hole in the front housing. Refer to illustration 1. Remove the plug (2) from the cylinder block. Install Tooling (C) into the Hole (Y) in the cylinder block. Use Tooling (C) in order to lock the crankshaft in the correct position.
Note: Do not use excessive force to install Tooling (C). Do not use Tooling (C) to hold the crankshaft during repairs.
- Install Tooling (B) through the hole (X) in the camshaft gear (1) into the front housing. Use Tooling (B) in order to lock the camshaft in the correct position.
Information System:
C4.4 Industrial Engine
Connecting Rod - Inspect
C4.4 Industrial Engine
Connecting Rod
390D Excavator Hydraulic System
Pilot Hydraulic System
390D Excavator Hydraulic System
Main Hydraulic System
Procedure to Repair Layered Doors on E Series Excavators{7273}
349E Excavator Hydraulic System
Travel Motor
320E and 323E Excavators
Cooling System Coolant Sample (Level 1) - Obtain
2010/06/23
Incorrect Use of the Engine Oil Drain Coupling on Some Large Excavators, Off-Highway Trucks/Tractors, Track-Type Tractors, Wheel Dozers, and Wheel Loaders {1306, 1308, 1318}
312D and 313D Excavators Machine System Specifications
Blade Cylinder Lines
312D and 313D Excavators Machine System Specifications
Blade Cylinder Lines
349E Excavator Hydraulic System
Control Valve (Stick Lowering)
Rust on D Series Excavators{0652}
C4.4 Industrial Engine
Fuel Injection Timing - Check
312D and 313D Excavators Machine System Specifications
Stick - 2.50 m (8.202 ft)
349E Excavator Hydraulic System
Bucket Hydraulic System
345D MHPU and 349D MHPU Mobile Hydraulic Power Units
Joystick Controls Alternate Patterns - If Equipped
2010/06/25
A New Multi Combined Function - Work Tool Valve (MCV) is Now Used on Certain Wheeled Excavators {5064}
320E and 323E Excavators
Engine Oil Level - Check
320E and 323E Excavators
Engine Oil and Filter - Change
450F Backhoe Loader Hydraulic and Steering System
Control Valve (Extendable Stick) (Mechanically Operated)
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators
Safety Messages
312D and 313D Excavators Machine System Specifications
Stick Cylinder
450F Backhoe Loader Hydraulic and Steering System
Control Valve (Boom) (Mechanically Operated)
2010/07/21
The Stick Support Pin Is Improved on Certain Small Excavators {6501}