PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System General Information Caterpillar


General Information
`


Illustration 1g06032103
PM620 Cold Planer

The diagnostics for the ECM can be accessed through one of the following tools: the Operator Monitoring System and Cat® Electronic Technician (Cat ET) Service Tool.

The Electrical System Schematic of the machine is shown in the Service Manual.

Refer to the appropriate media number below for the complete Electrical Schematic:

(S/N: JCF; LH9; 8RF; EL6) Machines refer to Electrical Schematic, UENR6397.

(S/N: JB9; JFC; LB8; FG4; TPH; XS6) Machines refer to Electrical Schematic, UENR6398.

(S/N: JB7; HN8; HC8; RL3; H6S; 626) Machines refer to Electrical Schematic, UENR8363.

(S/N: SL8; TLZ; ESE; AK5; AN8; EE2; E8S; 3C6; 627) Machines refer to Electrical Schematic, UENR8362.

The schematic will illustrate locations for all the electrical components and harness connectors that are installed on the machine.

As a guide, a typical system schematic is included at the end of this manual. For an accurate representation of the machine that is being diagnosed, refer to Electrical System Schematic in the Service Manual.

When the troubleshooting procedure instructs you to “REPAIR THE HARNESS OR REPLACE THE HARNESS”, use the Electrical System Schematic for the machine that is being serviced to trace the circuit. Perform continuity checks at the harness connectors to locate harness failures. At the connectors of the components, always check the ground circuit. Less than 5 ohms of resistance is required between the ground contacts of the connector and the frame ground. The power circuits of the ECM should have less than 2 ohms of resistance between the contacts of the ground connector and the frame ground. Less than 5 ohms of resistance is required for signal circuits for normal operation. Excessive ground resistance that is greater than 5 ohms can cause incorrect diagnosing of problems.

During troubleshooting, inspect all connections before any component is replaced. If these connections are not clean and tight, permanent electrical problems or intermittent electrical problems can result. Check that the wires are pushed into the connectors completely. Make sure that the connections are tight before other tests are made.

Failure of an electrical component can cause the failure of other components. Also, failure of an electrical component can be caused by the failure of other components. Always attempt to correct the cause of an electrical system failure before you replace a component.

Information System:

538 Forest Machine Machine Systems Cylinder Drift - Check - Empty Bucket
325F Excavator Machine Systems Travel Motor - Remove and Install
538 Forest Machine Machine Systems Swing Speed and Swing Drift on a Slope - Check
538 Forest Machine Machine Systems Swing Speed and Overswing on Level Ground - Check
538 Forest Machine Machine Systems Travel on Level Ground - Test
325F Excavator Machine Systems Counterbalance Valve (Travel) - Assemble
GSV520 and GSV525 Orange Peel Grapples Hydraulic Cylinder - Disassemble
314F and 315F Excavators Machine System Specifications Air Conditioner Lines
314F and 315F Excavators Machine System Specifications Communication Electronic Control Module (Product Link)
314F and 315F Excavators Machine System Specifications Communication Electronic Control Module (Product Link)
314F and 315F Excavators Machine System Specifications Cab Window
314F and 315F Excavators Machine System Specifications Blade Cylinder Lines
538 Forest Machine Machine Systems Cylinder Drift - Check - Loaded Bucket
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Service Tools
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Connector Locations
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Diagnostic Capabilities
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Symptom Troubleshooting
538 Forest Machine Machine Systems Cylinder Speed - Check
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Engine Performance - Test - Engine Speed
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Travel on Level Ground - Test
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Travel on Level Ground - Test - Optional Test
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Swing Speed and Overswing on Level Ground - Check
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Cylinder Drift - Check
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Cylinder Speed - Check