C9.3 Engines for Caterpillar Built Machines Fuel Pressure Is High Caterpillar

Fuel Pressure Is High

C9.3 Engines for Caterpillar Built Machines [KENR5393]

C9.3 Engines for Caterpillar Built Machines Engine Shutdown While Idling

C9.3 Engines for Caterpillar Built Machines Fuel Pressure Is Low

FUEL SYSTEM

C15 and C18 Petrolem Generator Set Engines Exhaust Has Excessive White Smoke

C9.3 Engines for Caterpillar Built Machines Fuel Consumption Is Excessive

C9.3 Engines for Caterpillar Built Machines Fuel Temperature Is High

C9.3 Engines for Caterpillar Built Machines Fuel Rail Pressure Is Low While Cranking

C9.3 Engines for Caterpillar Built Machines Fuel Rail Pressure Leakage Is High

C9.3 Engines for Caterpillar Built Machines Coolant Contains Fuel

C9.3 Engines for Caterpillar Built Machines Fuel Pressure Is High

System Operation Description:

The probable causes of high fuel pressure

Fuel pressure sensor
Fuel lines
Fuel transfer pump
Fuel return pressure regulator

Note: High fuel pressure may cause high fuel temperatures. Troubleshoot a code for high fuel pressure before troubleshooting a code for high fuel temperature.

Use this procedure in order to troubleshoot high fuel pressure. Use this procedure if one of the following event codes is active. Refer to Troubleshooting, "Event Codes" for information about event codes. For information on the engine monitoring system, refer to Troubleshooting, "Engine Monitoring System".

Show/hide table

Table 1
Event Code
CDL Code	Code Description	Comments
E096 (2)	High Fuel Pressure	The code is logged. The fuel pressure is above the trip point pressure.

Show/hide table

Table 2
Troubleshooting Test Steps	Values	Results
1. Check for Codes A. Connect Cat ET to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools", if necessary. B. Determine if a diagnostic trouble code is present.	Codes	Result: A E096 (2) code is present. Repair: Proceed to Test Step 2. Result: A code other than a E096 (2) code is present. Repair: Troubleshoot the code. Refer to the proper troubleshooting procedure. STOP

Show/hide table

Table 3
Required Tooling
8t-7860 Connector
110-6349 Fitting as
8t-0855 Pressure Gauge
6v-3990 Coupler

Show/hide table




Illustration 1	g02023390
(1) Fuel temperature sensor (2) Fuel sampling port (3) Fuel pressure sensor (4) Secondary fuel filter base

Note: Do not use the fuel sampling port (2) for measuring the pressure. Follow the steps below.

Show/hide table

Table 4
Troubleshooting Test Steps	Values	Results
2. Check the Fuel Pressure Sensor A. Record the fuel pressure from Cat ET. B. Remove the fuel pressure sensor (3). C. Install a 8T-7860 Connector into the port of the pressure sensor (3). D. Install the 110-6349 Fitting as onto the 8T-7860 Connector. E. Install a 8T-0855 Pressure Gauge onto a 6V-3990 Coupler. F. nstall the 6V-3990 Coupler onto the 110-6349 Fitting as. Note: After the pressure sensor is removed, a code for low fuel pressure will become active. Clear the code after the sensor is reinstalled.	Fuel Pressure	Result: The gauge value of the fuel pressure is within 137 kPa (20 psi) of the fuel pressure reading shown in ET. Proceed to Test Step 3. Result: The gauge value of the fuel pressure is not within 137 kPa (20 psi) of the fuel pressure reading shown in ET. Repair: Replace the pressure sensor. Verify that the problem has been resolved. If the problem is not resolved, proceed to Test Step 3.

Show/hide table




Illustration 2	g02023433
Fuel supply lines

Show/hide table




Illustration 3	g02024502
Return fuel line

Show/hide table

Table 5
Troubleshooting Test Steps	Values	Results
3. Inspect the Fuel Supply Lines A. Visually inspect the fuel lines between the primary filter base and the inlet to the cylinder head. Also, inspect the fuel cooler, if equipped. Inspect the fuel return line from the head to the fuel tank. Inspect the lines for restrictions, pinching, and swelling.	Fuel Supply Lines	Result: The fuel lines and the cooler (if equipped) are OK. Proceed to Test Step 4. Result: The fuel lines and the cooler (if equipped) are NOT OK. Repair: Make the necessary repairs. Verify that the problem has been resolved. If the problem is not resolved, proceed to Test Step 4.

Show/hide table




Illustration 4	g02024508
(5) Return fuel pressure regulator

Show/hide table

Table 6
Troubleshooting Test Steps	Values	Results
4. Replace the Fuel Pressure Regulator	Fuel Pressure Regulator	Result: The regulator was replaced. Verify that the problem is resolved. If the problem is not resolved, proceed to Test Step 5.

Show/hide table




Illustration 5	g02031818
Typical fuel transfer pump (6) Relief valve

Show/hide table

Table 7
Troubleshooting Test Steps	Values	Results
5. Inspect the Relief Valve for the Fuel Transfer Pump	Relief Valve	Result: The relief valve is stuck closed. Repair: Replace the fuel transfer pump. Verify that the problem has been resolved. STOP Result: The relief valve is OK. Repair: Clean the relief valve and reinstall the relief valve. Verify that the problem has been resolved. STOP

Test Step 1.

The procedure corrected the issue. Return to service.

Results:

The procedure did not correct the issue. -
Repair: Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).

STOP