Component Location
`
C9.3 Engines for Caterpillar Built Machines
[KENR5393]
C9.3 Engines for Caterpillar Built Machines
Sensor Calibration Required - Test
C9.3 Engines for Caterpillar Built Machines
Timing - Calibrate
ELECTRICAL AND STARTING SYSTEM
C9.3 Engines for Caterpillar Built Machines
Acceleration Is Poor or Throttle Response Is Poor
C9.3 Engines for Caterpillar Built Machines
Component Location
1.1. Electronic Control Circuit Diagram
2.1. Sensor Locations
3.1. View A
4.1. View B
5.1. View C
6.1. View D
7.1. View E
Electronic Control Circuit Diagram
Show/hide table
| |
| Illustration 1 | g02176508 |
|
Electronic system overview | |
Show/hide table
| |
| Illustration 2 | g02176512 |
|
(A) Refer to "View A" for a detailed illustration.
(B) Refer to "View B" for a detailed illustration. (C) Refer to "View C" for a detailed illustration. (D) Refer to "View D" for a detailed illustration. | |
Show/hide table
| |
| Illustration 3 | g02176515 |
| (E) Refer to "View E" for a detailed illustration. | |
Show/hide table
| |
| Illustration 4 | g02176525 |
|
(1) Fuel temperature sensor
(2) Fuel pressure sensor | |
Show/hide table
| |
| Illustration 5 | g02176528 |
|
(1) Camshaft speed/timing sensor
(2) Intake main air pressure sensor (3) Intake main air temperature sensor | |
Show/hide table
| |
| Illustration 6 | g02176536 |
|
(1) Barometric pressure sensor
(2) Oil pressure sensor | |
Show/hide table
| |
| Illustration 7 | g02176554 |
| (1) Crankshaft speed/timing sensor | |
Show/hide table
| |
| Illustration 8 | g02176559 |
| (1) Coolant temperature sensor | |
Information System:
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System
Hydraulic Pump - Test and Adjust
2010/07/08
New Gauges Available {7450}
314D Excavator
Lifting and Tying Down the Machine - Spreader Bar
390D Excavator Hydraulic System
Main Hydraulic Pump
390D Excavator Hydraulic System
Solenoid Valve (Proportional Reducing) - Power Shift System
390D Excavator Hydraulic System
Solenoid Valve (Hydraulic Lockout)
Replacement Procedure for the Service Repair Parts on the Multi-Processor Crusher Jaws{6349}
374D Excavator Hydraulic System
Swing Pump - Test - Constant Horsepower Flow Control
S365C and S385C Work Tools
Gear and Bearing - Remove and Install
Procedure for Reworking the HVAC Ducts on Certain Forestry Machines{734D}
349F and 352F Excavators Machine System
Displacement Change Valve
2010/06/30
A Check Valve Kit is Now Available for the Air Cleaner Assembly on Certain Backhoe Loaders {1050}
Installation Procedure for the 356-3680 Auxiliary Lines Group (Boom) {5057}
328D CR Excavator
Lifting and Tying Down the Machine - Rear Eyes and Front Eyes
311D, 312D, 312D2, 313D, 313D2, 314D, 315D, 318D, 318D2 and 319D Excavators Machine Electronic Control System
E-Ceiling and Cab Avoidance - Troubleshoot - Troubleshooting
349F and 352F Excavators Machine System
Travel Counterbalance Valve
374D Excavator Hydraulic System
Gear Pump (Pilot) - Test
325D and 329D Excavators
Securing the Machine
C9.3 Engines for Caterpillar Built Machines
Timing - Calibrate
390D Excavator Hydraulic System
Pump Control (Main Hydraulic)
311D, 312D, 312D2, 313D, 313D2, 314D, 315D, 318D, 318D2 and 319D Excavators Machine Electronic Control System
E-Fence - Set - Calibration
Installation Procedure for the 307-2964 Stick Lines Group on Certain 374D Excavators{5057}
390D Excavator Hydraulic System
Main Control Valve - Load Signal Regulation
390D Excavator Hydraulic System
Main Control Valve