320D2 GC Excavator Machine Systems Track Carrier Roller - Remove and Install Caterpillar


Track Carrier Roller - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
8T-5255  Hydraulic Jack 

  1. Start the engine. Park the machine on a hard, level surface. Shut off the engine.

    ------ WARNING! ------

    Personal injury or death can result from grease and oil coming out of the relief valve.

    Grease and oil are under high pressure coming out of the relief valve and can penetrate the body.

    Do not watch the relief valve to see if grease is escaping. Watch the track or track adjustment cylinder to see if the track is being loosened.

    Make sure the vent holes are clean before the tension is released on the track.




    Illustration 1g00489342

  2. Release the tension on the track.

  3. Loosen relief valve (1) by one turn only. If the track does not loosen after opening the relief valve, move the machine forward and backward until the tension is released.


    Illustration 2g00693935

  4. Loosen bolt (2) that holds track carrier roller (3) to the mounting bracket on the undercarriage.


    Illustration 3g00489356

  5. Position Tooling (A) and suitable cribbing under the track assembly, as shown.

  6. Use Tooling (A) in order to lift the track assembly off the track carrier roller.

  7. Remove track carrier roller (3). The weight of track carrier roller (3) is 17 kg (38 lb).

Reference: Refer to Undercarriage Reconditioning Bulletin, SEBF8568, "Hydraulic Excavator Roller Disassemble and Assembly Procedures" for the disassembly and assembly procedures for the track carrier roller.

Installation Procedure

  1. Make sure that the shaft of the track carrier roller and the bore in the mounting bracket on the undercarriage are clean and free of dirt.


    Illustration 4g00652868
    (x) Mounting bracket

  2. Place the track carrier roller in position in the mounting bracket. The weight of track carrier roller is 17 kg (38 lb). Adjust the carrier roller until Distance (a), the distance between the outside face of the mounting bracket and the carrier roller is 7.0 ± 0.5 mm (0.28 ± 0.02 inch).


    Illustration 5g00693935

  3. After you adjust the position of carrier roller (3) in the mounting bracket, tighten bolt (2).


    Illustration 6g00489356

  4. Make sure that carrier roller (3) rotates smoothly by manually turning the carrier roller.

  5. Slowly lower the track assembly onto the carrier roller with Tooling (A).

  6. Tighten the tension of the track. Refer to Operation and Maintenance Manual, "Track Adjustment - Adjust" for the correct procedure.

Information System:

320D2 GC Excavator Machine Systems Control Module (Automatic Temperature Control Unit) - Remove and Install
Rework Procedure for the Boom Nose on Certain 313D2 LGP Excavators {6501}
307E2 Mini Hydraulic Excavator Machine Systems Load Control Valve (Boom Cylinder) - Remove and Install
Improved Radiator Hoses and New Radiator Pipe Assemblies are Now Used on Certain 374F and 390F Excavators and Mobile Hydraulic Power Units {1380, 5057}
An Improved Hydraulic Tank is Now Used on Certain 374D and 390D Excavators {5056}
307E2 Mini Hydraulic Excavator Machine Systems Track - Connect
Procedure for Installing the Migration Kits on 320E and 323E Excavators {1250}
816K Landfill Compactor Capacities (Refill)
Aftertreatment Fuel Pumps May Fail on Certain Stage IIIB M300D Wheeled Excavators {1256}
C4.4 Engines DEF Pressure Does Not Respond
326F Excavator Access Door and Cover Locations
C9.3 Tier 4 Final Engines Water Pump
307E2 Mini Hydraulic Excavator Machine Systems Track - Separate
320D2 GC Excavator Machine Systems Track Roller - Remove and Install
320D2 GC Excavator Machine Systems Track - Separate
320D2 GC Excavator Machine Systems Track - Connect
320D2 GC Excavator Machine Systems Front Idler and Recoil Spring - Remove and Install
320D2 GC Excavator Machine Systems Recoil Spring - Disassemble
320D2 GC Excavator Machine Systems Recoil Spring - Assemble
An Improved Foot Valve Assembly and Valve Kit for the Fuel Transfer Pump is Now Available on Certain Excavators, Front Shovels, and Mobile Hydraulic Power Units {1256}
320D2 GC Excavator Machine Systems Hydraulic Track Adjusters - Disassemble
320D2 GC Excavator Machine Systems Hydraulic Track Adjusters - Assemble
320D2 GC Excavator Machine Systems Sprocket - Remove and Install
320D2 GC Excavator Machine Systems Counterbalance Valve (Travel) - Remove and Install