415F2 Industrial Loader Machine Systems Window Wiper and Wiper Motor (Front) - Remove and Install Caterpillar


Window Wiper and Wiper Motor (Front) - Remove and Install
`
415F2 Industrial Loader Machine Systems [M0067024]
OPERATOR STATION
WIPER GP-WINDOW
415F2 Industrial Loader Machine Systems Window Wiper and Wiper Motor (Front) - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Start By:

  1. Remove steering wheel.


    Illustration 1g01119509

  1. Remove bolts (3) and plate (2). Relocate floor mat (1).


    Illustration 2g03805502


    Illustration 3g03805511

  2. Remove cover (4). Disconnect harness assemblies (5). Remove cover (6).


    Illustration 4g03805494

  3. Remove cover (7). Separate lower panel (8) at Location (X). Remove lower panel (8).


    Illustration 5g03805517


    Illustration 6g03805580


    Illustration 7g03805587

  4. Remove bolts (9). Remove mat (10). Remove bolt (11).


    Illustration 8g03805595

  5. Lean cover assembly (12) rearward toward the steering column.


    Illustration 9g03805600

  6. Disconnect cable assembly (13) from the latch. Remove nut (14), feed the cable assembly (13) out of the bracket.

    Note: If hood were to close after removing cable assembly (13) there is no way to release the hood latch.



    Illustration 10g03805610


    Illustration 11g03805636

  7. Raise caps (15) and remove nuts (16). Remove nuts (17).


    Illustration 12g03805642

  8. Disconnect harness assembly (18). Remove front wiper motor (19).

Installation Procedure

  1. Install front wiper motor (19) in the reverse order of removal.


      Illustration 13g03805694


      Illustration 14g03805675

    1. Tighten nuts (17) to a torque of 15 N·m (133 lb in).

    2. Tighten wiper arm nut (16A) to a torque of 24 N·m (212 lb in), allow to relax for 30 minutes. Retorque to a torque if 24 N·m (212 lb in).

    3. Tighten wiper arm nut (16B) to a torque of 40 ± 5 N·m (30 ± 4 lb ft), allow to relax for 30 minutes. Retorque to a torque of 40 ± 5 N·m (30 ± 4 lb ft).

Information System:

415F2 Industrial Loader Machine Systems Steering Wheel - Remove and Install
415F2 Industrial Loader Machine Systems Steering Metering Pump - Remove and Install
320D2 GC Excavator Engine Supplement Engine - Remove and Install
415F2 Industrial Loader Machine Systems Hydraulic Tank - Remove and Install
415F2 Industrial Loader Machine Systems Piston Pump (Main Hydraulic) - Remove and Install
307E2 Mini Hydraulic Excavator Machine Systems Final Drive and Travel Motor - Remove
415F2 Industrial Loader Machine Systems Lift Arms - Remove and Install - Single Tilt
415F2 Industrial Loader Machine Systems Lift Cylinder - Remove and Install - Single Tilt
415F2 Industrial Loader Machine Systems Tilt Cylinder - Remove and Install - Single Tilt
415F2 Industrial Loader Machine Systems Bucket Positioner Control - Remove and Install - Single Tilt
349F XE and 352F XE Excavators Boom Hydraulic System - Health Check
New Software Is Now Available for all Cat Object Detection and Vision Applications On Certain Cat Products {7610, 7620}
415F2 Industrial Loader Machine Systems Canopy - Remove and Install
415F2 Industrial Loader Machine Systems Cab - Remove
415F2 Industrial Loader Machine Systems Cab - Install
415F2 Industrial Loader Machine Systems Refrigerant Accumulator - Remove and Install
C9.3 Tier 4 Final Engines Cylinder Head Valves
816K Landfill Compactor Transmission Magnetic Screen - Clean
GSV520 and GSV525 Orange Peel Grapples Head Assembly and Bushing - Remove and Install
An Improved Routing is Now Used for the Pilot Hose on Certain 336D2 and 340D2 Excavators {5057, 5059}
Improved Software is Available to Re-Flash the Monitor Software for Certain 307E2 Tier 4 Final Mini Hydraulic Excavators {7490, 7601, 7603, 7610, 7620}
An Improved Air Conditioning Compressor Is Used On Certain Wheeled Excavators {1152, 1802}
320D2 GC Excavator Engine Supplement Radiator and Hydraulic Oil Cooler - Remove and Install
320D2 GC Excavator Engine Supplement Radiator - Remove and Install