415F2 Industrial Loader Machine Systems Cab - Install Caterpillar


Cab - Install
`
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
386-6033  Lever Puller Hoist Gp 


    Illustration 1g06051664

    Note: Typical example.

  1. Attach Tooling (A) and a suitable lifting device to cab assembly (34). The weight of cab assembly (34) is approximately 1134 kg (2500 lb). Install cab assembly (34)


    Illustration 2g06051281

  2. Install bolts (33) through the cab assembly.


    Illustration 3g06051264

  3. Connect all ground straps (32) under the cab assembly.

    Note: Check for any ground straps and hose assemblies that may need to be attached to the cab assembly.



    Illustration 4g06051638

  4. Connect shifter assembly (31).


    Illustration 5g06051204

  5. Connect linkages (29) to loader control valve (30).


    Illustration 6g06032379


    Illustration 7g06032275

  6. Connect refrigerant hoses (28). Install duct assembly (26) and panel (27).


    Illustration 8g06051142


    Illustration 9g06051008

  7. Connect heater hoses (25). Install cover (24).


    Illustration 10g06041342


    Illustration 11g06041234

  8. Connect hose assemblies (23) to pilot valve (22).

  9. Install pilot valve (22) to base (20). Install bolts (21).


    Illustration 12g06032233


    Illustration 13g06032228

  10. Install panel (19) and panel assembly (18).


    Illustration 14g06051001

  11. Connect hose assemblies (15) and (16) to metering pump (17).


    Illustration 15g06050992

  12. Connect brake hose assemblies (13) and (14).


    Illustration 16g06050984

  13. Snap lower panel (12) into the upper panel.


    Illustration 17g06050746

  14. Install covers (11).


    Illustration 18g06050741


    Illustration 19g06050736

  15. Install lower cover (10). Connect harness assemblies (9). Install upper cover (8).


    Illustration 20g06050732

  16. Install cover (7) and pins (6).


    Illustration 21g06034314


    Illustration 22g06040680


    Illustration 23g03849691

  17. Connect harness assembly (5). Install plate assembly (4). Install bolts (3). Install floor mat (2) and plate (1).

  18. Charge the refrigerant in the air conditioner system. Refer to Service Manual, SENR5664, ""All Products Air Conditioning and Heating R-134a for All AVSpare Machines" for the correct procedure. Refer to Special Publication, NENG2500, ""Air Conditioning Tools"" for the correct tools."

End By:

  1. Install the steering wheel.

Information System:

415F2 Industrial Loader Machine Systems Cab - Remove
415F2 Industrial Loader Machine Systems Canopy - Remove and Install
415F2 Industrial Loader Machine Systems Window Wiper and Wiper Motor (Front) - Remove and Install
415F2 Industrial Loader Machine Systems Steering Wheel - Remove and Install
415F2 Industrial Loader Machine Systems Steering Metering Pump - Remove and Install
320D2 GC Excavator Engine Supplement Engine - Remove and Install
415F2 Industrial Loader Machine Systems Hydraulic Tank - Remove and Install
415F2 Industrial Loader Machine Systems Piston Pump (Main Hydraulic) - Remove and Install
307E2 Mini Hydraulic Excavator Machine Systems Final Drive and Travel Motor - Remove
415F2 Industrial Loader Machine Systems Lift Arms - Remove and Install - Single Tilt
415F2 Industrial Loader Machine Systems Lift Cylinder - Remove and Install - Single Tilt
415F2 Industrial Loader Machine Systems Tilt Cylinder - Remove and Install - Single Tilt
415F2 Industrial Loader Machine Systems Refrigerant Accumulator - Remove and Install
C9.3 Tier 4 Final Engines Cylinder Head Valves
816K Landfill Compactor Transmission Magnetic Screen - Clean
GSV520 and GSV525 Orange Peel Grapples Head Assembly and Bushing - Remove and Install
An Improved Routing is Now Used for the Pilot Hose on Certain 336D2 and 340D2 Excavators {5057, 5059}
Improved Software is Available to Re-Flash the Monitor Software for Certain 307E2 Tier 4 Final Mini Hydraulic Excavators {7490, 7601, 7603, 7610, 7620}
An Improved Air Conditioning Compressor Is Used On Certain Wheeled Excavators {1152, 1802}
320D2 GC Excavator Engine Supplement Radiator and Hydraulic Oil Cooler - Remove and Install
320D2 GC Excavator Engine Supplement Radiator - Remove and Install
Replacement Procedure for the Return Hose Assemblies on Certain 308E2 Excavators {5057, 5068}
320D2 GC Excavator Engine Supplement Hydraulic Oil Cooler - Remove and Install
415F2 Industrial Loader Machine Systems Air Conditioner and Heater - Remove and Install