415F2 Industrial Loader Machine Systems Refrigerant Accumulator - Remove and Install Caterpillar


Refrigerant Accumulator - Remove and Install
`
415F2 Industrial Loader Machine Systems [M0067024]
OPERATOR STATION
AIR CONDITIONER GP
415F2 Industrial Loader Machine Systems Refrigerant Accumulator - Remove and Install
415F2 Industrial Loader Machine Systems Air Conditioner and Heater - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

    ------ WARNING! ------

    Personal injury can result from contact with refrigerant.

    Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.

    Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.

    Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.

    Personal injury or death can result from inhaling refrigerant through a lit cigarette.

    Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.

    Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.

    Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.


  1. Recover the refrigerant. Refer to Service Manual, SENR5664, "All Products Air Conditioning and Heating R134a for All AVSpare Machines" for the recovery and charging procedure. Refer to Special Publication, NENG2500, "Air Conditioning Tools" for the correct tools.


    Illustration 1g03808056

  2. The refrigerant accumulator is at the rear of the machine, behind the rear axle. Disconnect hose assemblies (1) and (2). Remove bolt (4) and the clamp. Remove refrigerant accumulator (3).

Installation Procedure

  1. Install refrigerant accumulator (3) in the reverse order of removal.

Information System:

415F2 Industrial Loader Machine Systems Cab - Install
415F2 Industrial Loader Machine Systems Cab - Remove
415F2 Industrial Loader Machine Systems Canopy - Remove and Install
415F2 Industrial Loader Machine Systems Window Wiper and Wiper Motor (Front) - Remove and Install
415F2 Industrial Loader Machine Systems Steering Wheel - Remove and Install
415F2 Industrial Loader Machine Systems Steering Metering Pump - Remove and Install
320D2 GC Excavator Engine Supplement Engine - Remove and Install
415F2 Industrial Loader Machine Systems Hydraulic Tank - Remove and Install
415F2 Industrial Loader Machine Systems Piston Pump (Main Hydraulic) - Remove and Install
307E2 Mini Hydraulic Excavator Machine Systems Final Drive and Travel Motor - Remove
415F2 Industrial Loader Machine Systems Lift Arms - Remove and Install - Single Tilt
415F2 Industrial Loader Machine Systems Lift Cylinder - Remove and Install - Single Tilt
C9.3 Tier 4 Final Engines Cylinder Head Valves
816K Landfill Compactor Transmission Magnetic Screen - Clean
GSV520 and GSV525 Orange Peel Grapples Head Assembly and Bushing - Remove and Install
An Improved Routing is Now Used for the Pilot Hose on Certain 336D2 and 340D2 Excavators {5057, 5059}
Improved Software is Available to Re-Flash the Monitor Software for Certain 307E2 Tier 4 Final Mini Hydraulic Excavators {7490, 7601, 7603, 7610, 7620}
An Improved Air Conditioning Compressor Is Used On Certain Wheeled Excavators {1152, 1802}
320D2 GC Excavator Engine Supplement Radiator and Hydraulic Oil Cooler - Remove and Install
320D2 GC Excavator Engine Supplement Radiator - Remove and Install
Replacement Procedure for the Return Hose Assemblies on Certain 308E2 Excavators {5057, 5068}
320D2 GC Excavator Engine Supplement Hydraulic Oil Cooler - Remove and Install
415F2 Industrial Loader Machine Systems Air Conditioner and Heater - Remove and Install
415F2 Industrial Loader Machine Systems Fuel Tank - Remove and Install