307E2 Mini Hydraulic Excavator Machine Systems Refueling Pump - Remove and Install Caterpillar


Refueling Pump - Remove and Install
`
307E2 Mini Hydraulic Excavator Machine Systems [UENR6785]
FUEL SYSTEM
PUMP GP-FUEL TRANSFER
307E2 Mini Hydraulic Excavator Machine Systems Refueling Pump - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

------ WARNING! ------

Personal injury or death may result from failure to adhere to the following procedures.

Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire.

Clean up all leaked or spilled fuel. Do not smoke while working on the fuel system.

Turn the disconnect switch OFF or disconnect the battery when changing fuel filters.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


  1. Make sure that the fuel tank is no more than 3/4 full.


    Illustration 1g06022133

  1. Open cover (1).


    Illustration 2g06022150

  2. Disconnect harness assembly (5). Disconnect hoses (2). Remove four nuts (4). Remove refueling pump (3).

Installation Procedure

  1. Install refueling pump (3) in the reverse order of removal.

Information System:

415F2 Industrial Loader Machine Systems Fuel Tank - Remove and Install
415F2 Industrial Loader Machine Systems Air Conditioner and Heater - Remove and Install
320D2 GC Excavator Engine Supplement Hydraulic Oil Cooler - Remove and Install
Replacement Procedure for the Return Hose Assemblies on Certain 308E2 Excavators {5057, 5068}
320D2 GC Excavator Engine Supplement Radiator - Remove and Install
320D2 GC Excavator Engine Supplement Radiator and Hydraulic Oil Cooler - Remove and Install
An Improved Air Conditioning Compressor Is Used On Certain Wheeled Excavators {1152, 1802}
Improved Software is Available to Re-Flash the Monitor Software for Certain 307E2 Tier 4 Final Mini Hydraulic Excavators {7490, 7601, 7603, 7610, 7620}
An Improved Routing is Now Used for the Pilot Hose on Certain 336D2 and 340D2 Excavators {5057, 5059}
GSV520 and GSV525 Orange Peel Grapples Head Assembly and Bushing - Remove and Install
816K Landfill Compactor Transmission Magnetic Screen - Clean
C9.3 Tier 4 Final Engines Cylinder Head Valves
Installing the <NOBR>387-6451</NOBR> Ride Control Kit to a Machine That Has an ECM {5004}
Installing the <NOBR>387-6450</NOBR> Ride Control Kit to a Machine That Does Not Have an ECM {5004}
C9.3 Tier 4 Final Engines Fuel Injection Pump
C9.3 Tier 4 Final Engines Cylinder Head
GSV520 and GSV525 Orange Peel Grapples Rotator Motor and Manifold - Remove and Install
New Fuel Injection Pump Stop Solenoid is Available on Certain 3054C and C7.1 (Mech) Machine Engines {1251, 1259, 1264}
GSV520 and GSV525 Orange Peel Grapples Rotator Motor and Manifold - Disassemble
349D2 MHPU Mobile Hydraulic Power Unit Machine System Boom Cylinder Lines
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Rotator Motor and Manifold - Assemble
349D2 MHPU Mobile Hydraulic Power Unit Machine System Swing Motor Lines
349D2 MHPU Mobile Hydraulic Power Unit Machine System Fuel Tank
415F2 Industrial Loader Power Train Solenoid Valve (Transmission) - Remove and Install