GSV520 and GSV525 Orange Peel Grapples Rotator Motor and Manifold - Remove and Install Caterpillar


Rotator Motor and Manifold - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned to prevent dirt from entering the internal mechanism.


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g06022431

  1. Remove bolts (2) and cover assembly (1).


    Illustration 2g06022433

  2. Use two people to remove rotator motor and manifold (3). The weight of rotator motor and manifold (3) is approximately 23 kg (51 lb). Remove bolts (4). Remove rotator motor and manifold (3).

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
Loctite 243 

  1. Install rotator motor and manifold (3) in the reverse order of removal.

    1. Apply Tooling (A) to the threads of bolts (2) and bolts (4).

Information System:

C9.3 Tier 4 Final Engines Cylinder Head
C9.3 Tier 4 Final Engines Fuel Injection Pump
Installing the <NOBR>387-6450</NOBR> Ride Control Kit to a Machine That Does Not Have an ECM {5004}
Installing the <NOBR>387-6451</NOBR> Ride Control Kit to a Machine That Has an ECM {5004}
307E2 Mini Hydraulic Excavator Machine Systems Refueling Pump - Remove and Install
415F2 Industrial Loader Machine Systems Fuel Tank - Remove and Install
415F2 Industrial Loader Machine Systems Air Conditioner and Heater - Remove and Install
320D2 GC Excavator Engine Supplement Hydraulic Oil Cooler - Remove and Install
Replacement Procedure for the Return Hose Assemblies on Certain 308E2 Excavators {5057, 5068}
320D2 GC Excavator Engine Supplement Radiator - Remove and Install
320D2 GC Excavator Engine Supplement Radiator and Hydraulic Oil Cooler - Remove and Install
An Improved Air Conditioning Compressor Is Used On Certain Wheeled Excavators {1152, 1802}
New Fuel Injection Pump Stop Solenoid is Available on Certain 3054C and C7.1 (Mech) Machine Engines {1251, 1259, 1264}
GSV520 and GSV525 Orange Peel Grapples Rotator Motor and Manifold - Disassemble
349D2 MHPU Mobile Hydraulic Power Unit Machine System Boom Cylinder Lines
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Rotator Motor and Manifold - Assemble
349D2 MHPU Mobile Hydraulic Power Unit Machine System Swing Motor Lines
349D2 MHPU Mobile Hydraulic Power Unit Machine System Fuel Tank
415F2 Industrial Loader Power Train Solenoid Valve (Transmission) - Remove and Install
415F2 Industrial Loader Power Train Transmission (Direct Drive) - Remove
325F Excavator Engine Supplement Engine - Remove and Install
415F2 Industrial Loader Power Train Transmission (Direct Drive) - Disassemble
325F Excavator Machine Systems Fuel Tank - Remove and Install
415F2 Industrial Loader Power Train Transmission (Direct Drive) - Assemble