GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Swivel - Disassemble Caterpillar


Swivel - Disassemble
`
1.1. Disassembly Procedure

Disassembly Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
8B-7551  Bearing Puller Gp 

Start by:

a. Remove the hydraulic rotator.

Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected always.

Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.



    Illustration 1g06023318

  1. Remove plugs (4), bolts (1), lock plate (2), and ring (3).


    Illustration 2g06023319
    Typical example


    Illustration 3g06023322

  2. Use Tooling (A) and a suitable press to remove stator (5).

  3. Remove stator (5).

  4. Remove bearing (9), seal assemblies (8), and bearing (6) from rotor (7).

Information System:

A New Fuel Injection Pump Group is Used on Certain C9.3 Machine Engines {1251}
Installation Procedure to Retrofit a Boom Lowering Control Valve on Certain 568 LL Forestry Machines {1329, 1439, 1916, 1917, 1923, 1924, 5001, 5117, 5130, 5264, 5453}
415F2 Industrial Loader Power Train Axle Shaft - Remove and Install
415F2 Industrial Loader Power Train Axle Housing and Flange - Install
415F2 Industrial Loader Power Train Axle Housing and Flange - Assemble
415F2 Industrial Loader Power Train Axle Housing and Flange - Disassemble
Installation Procedure to Retrofit a Boom Lowering Control Valve on Certain 325D Forestry Machines {5057, 5147, 5811}
304.5E XTC Mini Hydraulic Excavators Machine Systems Pilot Valve (Joystick) - Remove and Install
415F2 Industrial Loader Power Train Final Drive Planetary - Remove and Install - Front
415F2 Industrial Loader Power Train Axle Housing and Flange - Remove
Similar Product Support Literature Available For Military Machines {0374, 1000, 7000}
330F MHPU Mobile Hydraulic Power Unit Maintenance Interval Schedule
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Swivel - Assemble
345D, 349D and 349D2 Excavator Machine System Specifications Control Valve
GSV520 and GSV525 Orange Peel Grapples Shell Assembly - Remove and Install
325F Excavator Machine Systems Heating and Air Conditioning Unit - Remove and Install
Installation of the <NOBR>492-1508</NOBR> Auxiliary Control Ar on Certain Hydraulic Excavators {1408, 5258, 7405, 7557}
Installation of the <NOBR>327-7487</NOBR> Foot Pedal Gp on Certain Hydraulic Excavators {5258}
Installation of the <NOBR>360-6218</NOBR> Electronic Control Wiring Gp on Certain Hydraulic Excavators {1408}
415F2 Industrial Loader Power Train Axle Housing (Differential and Bevel Gear) (Front) - Disassemble
415F2 Industrial Loader Power Train Axle Housing (Differential and Bevel Gear) (Front) - Assemble
415F2 Industrial Loader Power Train Drive and Steering Axle (Front) - Remove
415F2 Industrial Loader Power Train Drive and Steering Axle (Front) - Install
325F Excavator Machine Systems Track Roller - Remove and Install