415F2 Industrial Loader Power Train Drive and Steering Axle (Front) - Remove Caterpillar


Drive and Steering Axle (Front) - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
422-8733  Support Stand 
444-0526  Air/Hydraulic Jack Gp 

Start By:

  1. Remove the bucket.


    Illustration 1g06043550

    Note: Typical example.

  1. Raise the lift arms and install lift cylinder brace (1).


    Illustration 2g06043491

  2. Use Tooling (B) to raise the front of the machine. Position two of Tooling (A) under the front of the machine.

  3. Remove the front fenders.

  4. Remove the front tires and rims.

  5. Remove the batteries.


    Illustration 3g03764858

  6. Disconnect both hose assemblies (2).


    Illustration 4g03764901

  7. Disconnect drive shaft (3).


    Illustration 5g03764917


    Illustration 6g03765837


    Illustration 7g03765882

  8. Remove bolt (4).

  9. Attach a suitable lifting device to both sides of front drive and steering axle (6). The weight of front drive and steering axle (6) is approximately 408 kg (900 lb).

  10. Remove pin assembly (5). Remove front drive and steering axle (6). Remove washers (8) and (9) and thrust washers (7) and (10) from front drive and steering axle (6).


    Illustration 8g03765904

  11. Remove seal (11). Remove bushing (12). Repeat this step for the other side.

Information System:

415F2 Industrial Loader Power Train Axle Housing (Differential and Bevel Gear) (Front) - Assemble
415F2 Industrial Loader Power Train Axle Housing (Differential and Bevel Gear) (Front) - Disassemble
Installation of the <NOBR>360-6218</NOBR> Electronic Control Wiring Gp on Certain Hydraulic Excavators {1408}
Installation of the <NOBR>327-7487</NOBR> Foot Pedal Gp on Certain Hydraulic Excavators {5258}
Installation of the <NOBR>492-1508</NOBR> Auxiliary Control Ar on Certain Hydraulic Excavators {1408, 5258, 7405, 7557}
325F Excavator Machine Systems Heating and Air Conditioning Unit - Remove and Install
GSV520 and GSV525 Orange Peel Grapples Shell Assembly - Remove and Install
345D, 349D and 349D2 Excavator Machine System Specifications Control Valve
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Swivel - Assemble
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Swivel - Disassemble
A New Fuel Injection Pump Group is Used on Certain C9.3 Machine Engines {1251}
Installation Procedure to Retrofit a Boom Lowering Control Valve on Certain 568 LL Forestry Machines {1329, 1439, 1916, 1917, 1923, 1924, 5001, 5117, 5130, 5264, 5453}
415F2 Industrial Loader Power Train Drive and Steering Axle (Front) - Install
325F Excavator Machine Systems Track Roller - Remove and Install
325F Excavator Machine Systems Track - Separate
GSV520 and GSV525 Orange Peel Grapples Hydraulic Cylinder - Remove and Install
340F Excavator Guards - Operator Protection
340F Excavator Shipping the Machine
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Sensor Signal (Analog, Active) - Test
415F2 Industrial Loader Power Train Steering Cylinder (Front) - Remove and Install
538, 548 and 558 Forest Machine Diagnostic Trouble Codes
538, 548 and 558 Forest Machine Event Codes
415F2 Industrial Loader Power Train Rear Axle - Remove
415F2 Industrial Loader Power Train Rear Axle - Install