415F2 Industrial Loader Power Train Rear Axle - Remove Caterpillar


Rear Axle - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
286-7889  Jack Stand Gp 
283-1478 Tube 
283-1500 Pin As 
1U-7505  Hydraulic Jack 

Start By:

  1. Remove blade assembly.


    Illustration 1g01260063

  1. Loosen lug nuts (1). Do not remove lug nuts (1) at this time. Repeat this step for the opposite side.


    Illustration 2g06042106

  2. Raise the rear of the machine. Install Tooling (A), as shown. Lower the machine onto Tooling (A).

  3. Release the system pressure.


    Illustration 3g02920158

  4. Secure rear tire and rim (2) to a suitable power truck. Remove lug nuts (1) (not shown). Use the suitable power truck to remove rear tire and rim (2). The weight of rear tire and rim (2) is approximately 175 kg (385 lb). Repeat this step for the opposite side of the machine.


    Illustration 4g06042173

  5. Remove rear drive shaft (3).


    Illustration 5g06042537


    Illustration 6g06042710

  6. Disconnect hose assembly (4). Disconnect hose assemblies (5).


    Illustration 7g06042739


    Illustration 8g06042744

  7. Disconnect brake clevis (6) and (7).


    Illustration 9g06042753


    Illustration 10g06043104


    Illustration 11g06043090

  8. Secure rear axle assembly (8) to Tooling (B) with suitable chains. The weight of rear axle assembly (8) is approximately 580 kg (1279 lb).

  9. Remove cover (9). Repeat this step for the opposite side.

  10. Remove bolts (10), nuts, and washers, remove rear axle assembly (8).

Information System:

538, 548 and 558 Forest Machine Event Codes
538, 548 and 558 Forest Machine Diagnostic Trouble Codes
415F2 Industrial Loader Power Train Steering Cylinder (Front) - Remove and Install
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Sensor Signal (Analog, Active) - Test
340F Excavator Shipping the Machine
340F Excavator Guards - Operator Protection
GSV520 and GSV525 Orange Peel Grapples Hydraulic Cylinder - Remove and Install
325F Excavator Machine Systems Track - Separate
325F Excavator Machine Systems Track Roller - Remove and Install
415F2 Industrial Loader Power Train Drive and Steering Axle (Front) - Install
415F2 Industrial Loader Power Train Drive and Steering Axle (Front) - Remove
415F2 Industrial Loader Power Train Axle Housing (Differential and Bevel Gear) (Front) - Assemble
415F2 Industrial Loader Power Train Rear Axle - Install
415IL Backhoe Loader Power Train Axle Housing, Axle Shaft, and Wheel Flange - Remove - Rear Axle
415IL Backhoe Loader Power Train Axle Housing, Axle Shaft, and Wheel Flange - Disassemble - Rear Axle
352F Mobile Hydraulic Power Unit (MHPU) Machine Systems Specifications
GSV520 and GSV525 Orange Peel Grapples Bushings (Shell Assembly) - Remove and Install
C9 Engines for Caterpillar Built Machines Piston and Rings
Technical Analysis 1 (TA1) Visual Inspection for Paving Compactors {0372, 1000, 7000, 753S, 7565}
C9 Engines for Caterpillar Built Machines Cylinder Liner
349F XE and 352F XE Excavators Shipping the Machine
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems Water Spray Lines
538, 548 and 558 Forest Machine Sensor Signal (PWM) - Test
538, 548 and 558 Forest Machine Sensor Signal (Analog, Passive) - Test