Tire and Rim (Rear) - Remove and Install
`
415F2 Industrial Loader Power Train
[M0067026]
POWER TRAIN
WHEEL GP
415F2 Industrial Loader Power Train
Axle Shaft - Remove and Install
415F2 Industrial Loader Power Train
Tire and Rim (Front) - Remove and Install
415F2 Industrial Loader Power Train
Tire and Rim (Rear) - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 444-0526 | Manual/Hydraulic Jack | 1 |
B | 422-2352 | Support Stand | 2 |
C | 222-3123 | Penetrating Oil | - |
- Loosen lug nuts (1). Do not remove lug nuts (1) at this time.
Show/hide table
Illustration 2 g01153151 - Use Tooling (A) to raise the rear of the machine. Position Tooling (B) under the rear axle. Lower the machine onto Tooling (B).
Show/hide table
Illustration 3 g02919717 - Secure tire and rim (2) to a suitable power truck. Remove lug nuts (1) (not shown). Use the suitable power truck to remove tire and rim (2). The weight of tire and rim (2) is approximately
175 kg (386 lb) .
Show/hide table
![]() | |
Illustration 1 | g01516986 |
- Install tire and rim (2) in the reverse order of removal.
- Apply one drop of Tooling (C) to the threads of lug nuts (1).
- Tighten lug nuts (1) to a torque of
460 ± 60 N·m (340 ± 44 lb ft) . Use a star pattern to tighten lug nuts (1).
Note: Clean all studs and lug nuts (1).
Information System:
340F Excavator
Safety Messages
415F2 Industrial Loader Power Train
Tire and Rim (Front) - Remove and Install
415F2 Industrial Loader Power Train
Axle Housing (Service Brakes, Differential and Bevel Gear) - Assemble
415F2 Industrial Loader Power Train
Axle Housing (Service Brakes, Differential and Bevel Gear) - Disassemble
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System
Condition Switch (Switch to Ground) - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System
Solenoid Return - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System
Sensor Signal (Analog, Passive) - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System
ECM Location Code - Test
415IL Backhoe Loader Power Train
Axle Housing, Axle Shaft, and Wheel Flange - Install - Rear Axle
538, 548 and 558 Forest Machine
Window Wiper Delay - Test
538, 548 and 558 Forest Machine
Switch Circuits - Test
538, 548 and 558 Forest Machine
Solenoid Valve (Switch Controlled) - Test
340F Excavator
Boom/Stick/Bucket Combinations
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems
Air Conditioner Lines
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems
Air Conditioner Lines
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems
Control Valve
Improved Diesel Oxidation Catalyst (DOC) Is Used On Certain D Series Wheeled Excavators {1091}
BH150 Backhoes and BH160 Backhoes For Skid Steer Loaders and Multi Terrain Loaders
Shipping
New K Series GET Adapters are Available on Certain Excavators and Wheel Loaders Buckets {6001, 6800, 6803}
C9 Engines for Caterpillar Built Machines
Cylinder Head Valves
C9 Engines for Caterpillar Built Machines
Unit Injector Hydraulic Pump
349F XE and 352F XE Excavators
Engine Oil Level - Check
New K Series GET Tips are Now Available for Certain Excavators and Wheel Loaders Buckets {6800, 6805}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train
Track