Alternator - Remove and Install
`
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
[UENR7319]
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Assemble
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Water Temperature Regulator - Remove and Install
ELECTRICAL AND STARTING SYSTEM
ALTERNATOR GP-CHARGING
303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement
Alternator - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Alternator - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Alternator - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Alternator - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
 |
|
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
- Open the hood.
- Turn the disconnect switch to the OFF position.
Show/hide table
Illustration 1 g06027039 - Remove bolt (1) and the washers. Remove panel (2).
Show/hide table
Illustration 2 g06027050 - Disconnect cable assembly (5). Disconnect harness assembly (6). Loosen bolt (3) and remove the belt from alternator (4). Remove bolt (3) and bolt (7). Remove alternator (4).
- Install alternator (4). Install the washer and bolt (7) loosely. Install the washer and bolt (3) loosely.
- Install the belt and adjust the belt to the proper tension. Refer to Operation and Maintenance Manual for the correct adjustment procedure. Tighten bolt (7) and bolt (3).
- Connect harness assembly (6). Connect cable assembly (5).
Show/hide table
Illustration 4 g06027039 - Install cover (2). Install bolts (1).
- Turn the disconnect switch to the ON position.
Show/hide table
| |
| Illustration 3 | g06027050 |
Information System:
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Operator Console
Installation Master Guide for the <NOBR>503-4975</NOBR> Auxiliary Control Ar on Certain Hydraulic Excavators {5051}
Installation of the <NOBR>255-2082</NOBR> Pilot Lines Gp on Certain Hydraulic Excavators {5057, 5059}
An Improved Power Converter is Available for Certain Excavators {7338}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Lines (Conveyor) - Motor
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Steering Cylinder
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Lines (Conveyor)
New Cat Grade Control / Cat Production Measurement Software is Now Available on Certain 336F XE and 349F XE Excavators {7494, 7610, 7620}
415F2 Backhoe Loaders Hydraulic and Steering System
Service Brake Control
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Mounting Bracket - Control
Technical Analysis 1 (TA1) Visual Inspection for Wheeled Excavator {0372, 1000, 7000, 753S, 7565}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Fuel Tank
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Conveyor System
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Electronic Control Module
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Track Roller (Single Flange)
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Control Valve and Mounting
301.7D CR Mini Hydraulic Excavator
Track Adjustment - Inspect
336D 2L and 340D 2L Excavators Machine Systems
Swing Gear and Bearing - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Heating and Air Conditioning Unit - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Heater Core - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Evaporator Coil - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Cab - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Fuel Tank - Remove and Install
Improved Hoses Are Now Used on Certain Backhoe Loaders {5057}