Fuel Tank - Remove and Install
`
336D 2L and 340D 2L Excavators Machine Systems
[M0065626]
336D 2L and 340D 2L Excavators Machine Systems
Cab - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Hydraulic Lockout Control - Remove and Install
FUEL SYSTEM
TANK GP-FUEL
336D 2L and 340D 2L Excavators Machine Systems
Fuel Tank - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 189-0408 | Shackle As | 2 |
B | 422-5473 | Lifting Eye Assembly | 2 |
C | - | Loctite 263 | - |
Show/hide table
![]() |
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (2) and plate assembly (1).
- Remove bolts (4) and plate assembly (3).
- Drain the fuel tank into a suitable container for storage or disposal. The capacity of the fuel tank is approximately
621 L (164 US gal) . - Open the right rear access door.
Show/hide table
Illustration 2 g03877036 - Remove cover (5).
Show/hide table
Illustration 3 g06029097 Show/hide tableIllustration 4 g06029102 - Remove handrail assembly (7) and bolts (6).
- Remove handrail assembly (10) and bolts (9). Remove bolts (8).
- Remove bolts (11) and cover (12). Use two people to remove cover assembly (12). The weight of cover assembly (12) is approximately
23.81 kg (53 lb) .Show/hide tableIllustration 5 g06029103 - Remove cable straps (13) and (14). Reposition the harness assemblies.
Show/hide table
Illustration 6 g06029104 - Remove clip (16) and hose assembly (15).
Show/hide table
Illustration 7 g06029106 - Disconnect hoses (17) and (18). Remove clips (19).
Show/hide table
Illustration 8 g06029133 Show/hide tableIllustration 9 g06029136 - Attach Tooling (A), Tooling (B), and a suitable lifting device to fuel tank (20). The weight of fuel tank (20) is approximately
251 kg (554 lb) . - Remove bolts (21) and remove fuel tank (20).
Show/hide table
![]() | |
Illustration 1 | g02154208 |
- Attach tooling (A), tooling (B), and suitable lifting device to install fuel tank (20).
Show/hide table
Illustration 11 g06029136 - Apply tooling (C) to bolt (21). Install bolt (21) to the bottom of fuel tank (20).
Show/hide table
Illustration 12 g06029106 - Connect hoses (17) and (18). Tighten the clamps for hoses (17) and (18) to a torque of
1.4 ± .3 N·m (12.4 ± 2.7 lb in) . Install clips (19).Show/hide tableIllustration 13 g06029104 - Install hose assembly (15) and clip (16).
Show/hide table
Illustration 14 g06029103 - Install cable straps (13) and (14) to the harness assemblies.
Show/hide table
Illustration 15 g06029102 Show/hide tableIllustration 16 g06029097 - Install cover (12) and bolts (11). Install Bolts (8).
- Install handrail assembly (10) and bolts (9).
- Install handrail assembly (7) and bolts (6).
Show/hide table
Illustration 17 g03877036 - Install cover (5).
Show/hide table
Illustration 18 g02154208 - Apply tooling (C) to the threads of bolts (2) and (4).
- Install plate assembly (3) and bolt (4).
- Install plate assembly (1) and bolt (2).
Show/hide table
![]() | |
Illustration 10 | g06029133 |
Information System:
336D 2L and 340D 2L Excavators Machine Systems
Cab - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Evaporator Coil - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Heater Core - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Heating and Air Conditioning Unit - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Swing Gear and Bearing - Remove and Install
301.7D CR Mini Hydraulic Excavator
Track Adjustment - Inspect
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Control Valve and Mounting
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Track Roller (Single Flange)
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Electronic Control Module
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Conveyor System
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Alternator - Remove and Install
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Operator Console
Improved Hoses Are Now Used on Certain Backhoe Loaders {5057}
New Rear Axle and Brake Control Groups Are Now Used On Certain 424B Backhoe Loaders {3278, 3282, 4269}
352F Mobile Hydraulic Power Unit (MHPU) Machine System
Main Hydraulic System
336D 2L and 340D 2L Excavators Machine Systems
Hydraulic Lockout Control - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Window Wiper Motor - Remove and Install - Lower
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples
Head Assembly and Bushing - Remove and Install
349F and 352F Excavators
Joystick Controls - Cat Grade With Assist System
314F and 315F Excavators Machine System Specifications
Control Valve (Auxiliary)
An Improved Main Control Valve is Now Used on 308E2 CR and 308E2 SR Mini Hydraulic Excavators {5051}
314F and 315F Excavators Machine System Specifications
Chassis Lighting
349F and 352F Excavators
Monitoring System - Monitor with Installed Cat Grade With Assist
307 Hydraulic Excavator Engine Supplement
Refrigerant Compressor - Remove and Install