Bucket Linkage Bearings and Seals - Remove and Install
`
336D 2L and 340D 2L Excavators Machine Systems
[M0065626]
336D 2L and 340D 2L Excavators Machine Systems
Bucket Linkage - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Stick - Remove and Install
IMPLEMENTS
LINKAGE GP
336D 2L and 340D 2L Excavators Machine Systems
Bucket Linkage - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Bucket Linkage Bearings and Seals - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 350-7768 | Electric Hydraulic Pump | 1 |
9U-6832 | Fast Runner Nut Assembly | 1 | |
4C-9634 | Puller Stud | 1 | |
5P-2998 | Cylinder | 1 | |
6V-2097 | Receiving Sleeve | 1 | |
9U-5337 | (1) Bearing Puller Adapter | 1 | |
9U-5339 | (2) Bearing Puller Adapter | 1 |
Show/hide table
(1) | This bearing puller adapter is for the bearing in the linkage pin bore of the stick. |
(2) | The bearing puller adapter that is shown is for the bearings in the linkage assembly. |
Start By:
a. Remove the bucket linkage.
- Remove lip seal (1).
Show/hide table
Illustration 2 g00619100 - Use Tooling (A) to remove the sleeve bearing from the pin bore.
- Repeat Steps 1 and 2 to remove the lip seal and the sleeve bearing from the other side of the stick.
Show/hide table
Illustration 3 g01213578 - Remove lip seals (2).
Show/hide table
Illustration 4 g01213579 - Use Tooling (A) to remove the sleeve bearing from the pin bore.
- Repeat Steps 4 and 5 remove the lip seals and the sleeve bearing from the other side of the linkage assembly.
Show/hide table
Illustration 5 g01213583 - Remove lip seal (3) from the linkage assembly.
Show/hide table
Illustration 6 g01213584 - Use Tooling (A) to remove the sleeve bearing from the pin bore.
- Repeat Steps 7 and 8 to remove the lip seal and the sleeve bearing from the other side of the linkage assembly.
Show/hide table
![]() | |
Illustration 1 | g00619083 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
B | 1P-0520 | Bearing and Seal Driver | 1 |
- Lower the temperature of the sleeve bearing. Use Tooling (A) to install the sleeve bearing in the linkage assembly. Install the sleeve bearing until Dimension (a) is
9.5 ± 0.8 mm (0.37 ± 0.03 inch) below the outside surface of the linkage assembly.Show/hide tableIllustration 8 g01214570 - Use Tooling (A) to install lip seal (3). Install lip seal (3) with the sealing lip toward the outside of the linkage assembly. Install lip seal (3) until lip seal (3) contact with the sleeve bearing.
- Repeat Steps 1 and 2 for the installation of the remaining lip seal and sleeve bearing.
Show/hide table
Illustration 9 g01214571 (X) Bucket control linkage
(Y) Sleeve bearing - Lower the temperature of the sleeve bearing. Use Tooling (A) to install the sleeve bearing. Install the sleeve bearing until Dimension (b) is
9.5 ± 0.8 mm (0.37 ± 0.03 inch) below the outside surface of the linkage assembly.Show/hide tableIllustration 10 g01214572 - Use Tooling (A) to install lip seals (2). Install lip seals (2) with the sealing lip toward the outside of the linkage assembly. Install lip seals (2) until lip seals (2) contact with the sleeve bearing.
- Repeat Steps 4 and 5 for the installation of the remaining lip seal and sleeve bearing.
Show/hide table
Illustration 11 g01214576 (Y) Sleeve bearing
(Z) Stick - Lower the temperature of the sleeve bearing. Use Tooling (A) to install the sleeve bearing in the stick. Install the sleeve bearing until dimension (c) is
9.5 ± 0.8 mm (0.37 ± 0.03 inch) below the outside surface of the stick.Show/hide tableIllustration 12 g01214574 - Use Tooling (A) to install lip seal (1). Install lip seal (1) with the sealing lip toward the outside of the stick. Install lip seal (1) until lip seal (1) contact with the sleeve bearing.
- Repeat Steps 7 and 8 for the installation of the remaining lip seal and sleeve bearing.
End By:
a. Install the bucket linkage.
Show/hide table
![]() | |
Illustration 7 | g01214568 |
(X) Bucket control linkage
(Y) Sleeve bearing |
Information System:
314F and 315F Excavators Machine System Specifications
Front Lines
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples
Hydraulic Cylinder - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Bucket Linkage - Remove and Install
314F and 315F Excavators Machine System Specifications
Front Lines
316F Excavator Machine System Specifications
Bucket Cylinder
314F and 315F Excavators Machine System Specifications
Boom Cylinder
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples
Shell Assembly - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Bucket - Remove and Install
314F and 315F Excavators Machine System Specifications
Pump Lines
314F and 315F Excavators Machine System Specifications
Stick Cylinder Lines
314F and 315F Excavators Machine System Specifications
Main Control Valve
314F and 315F Excavators Machine System Specifications
Stick Cylinder Lines
336D 2L and 340D 2L Excavators Machine Systems
Stick - Remove and Install
349D2 MHPU Mobile Hydraulic Power Unit (OEM)
Maintenance Interval Schedule
374F Excavator Machine Systems
Main Hydraulic Pump - Disassemble
374F Excavator Machine Systems
Main Hydraulic Pump - Assemble
Four-point Seat Belts are Now Available for Certain Excavators and Track Feller Bunchers {7312}
Buttons are Now Used When Installing Bonded Glass {7301}
314F and 315F Excavators Machine System Specifications
Pilot Lines
314F and 315F Excavators Machine System Specifications
Pilot Valve
314F and 315F Excavators Machine System Specifications
Pilot Valve
Electric Starting Motor on Certain C7.1 Machine Engines {1453}
314F and 315F Excavators Machine System Specifications
Pilot Lines
336D 2L and 340D 2L Excavators Machine Systems
Stick Bearings and Seals - Remove and Install