336D 2L and 340D 2L Excavators Machine Systems Pressure Reducing Valve (Implement and Swing Priority) - Remove and Install Caterpillar


Pressure Reducing Valve (Implement and Swing Priority) - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Start By:

a. Release the hydraulic system pressure.


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.



    Illustration 1g01206148

  1. Remove bottom panel (1).


    Illustration 2g01206151

  2. Disconnect hose assemblies (2). Remove bolts (3) and remove pressure reducing valve (4).

Installation Procedure



    Illustration 3g01206151

  1. Install pressure reducing valve (4) and install bolts (3). Connect hose assemblies (2).


    Illustration 4g01206148

  2. Install bottom panel (1).

Information System:

538 Forest Machine Machine Systems Travel Motor - Test - Measurement of Case Drain Oil
308E2 CR, 308E2 SR Mini Hydraulic Excavator Diagnostic Trouble Codes
336D 2L and 340D 2L Excavators Machine Systems Gear Pump (Pilot) - Remove and Install
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Final Drive and Wheel
538 Forest Machine Machine Systems Relief Valve (Swing) - Test and Adjust
325F Excavator Engine Supplement Diesel Exhaust Fluid Pump - Remove and Install
Debris in Oil System Causing Repeat Failures of the (HEUI) Pump for Certain C7 and C9 Engines. {1126, 1251, 1318, 1378}
Procedure for Reinforcing Bracket As on Certain M Series Motor Graders {6158, 6159}
538 Forest Machine Machine Systems Swing Motor - Test - Measurement of Case Drain Oil
336D 2L and 340D 2L Excavators Machine Systems Main Control Valve - Remove and Install
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Differential
558 Forest Machine Machine Systems Relief Valve (Main) - Test and Adjust
Retrofitting Boom Lowering Control Valve/Stick Lowering Control Valve on 345D/349D/349D2 Excavators {5051, 5057, 5059, 5456, 5458}
926M, 930M and 938M Wheel Loaders Power Train Piston Motor (Hydrostatic) - Disassemble - Front Hydrostatic Piston Motor
926M, 930M and 938M Wheel Loaders Power Train Piston Motor (Hydrostatic) - Assemble - Front Hydrostatic Piston Motor
926M, 930M and 938M Wheel Loaders Power Train Piston Motor (Hydrostatic) - Disassemble - Rear Hydrostatic Piston Motor
926M, 930M and 938M Wheel Loaders Power Train Piston Motor (Hydrostatic) - Assemble - Rear Hydrostatic Piston Motor
538 Forest Machine Machine Systems Relief Valve (Crossover) - Test and Adjust
Counterbalance Valves Are Now Used on Certain Hydraulic Excavator Forestry Grapples {5362, 5457, 5555, 6307}
336D2/336D2 GC Excavator Engine Supplement Turbocharger - Remove and Install
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Gear Motor (Hydraulic Fan)
336D 2L and 340D 2L Excavators Machine Systems Hydraulic Tank - Remove and Install
538 Forest Machine Machine Systems Process for Setting Up the Work Tool
325F Excavator Machine Systems Final Drive - Disassemble