Air Cleaner - Remove and Install
`
312C Excavator 3064 Engine Supplement
[RENR5507]
312C Excavator 3064 Engine Supplement
Turbocharger - Install
312C Excavator 3064 Engine Supplement
Water Pump - Remove
AIR INLET AND EXHAUST SYSTEM
AIR CLEANER GP
312C Excavator 3064 Engine Supplement
Air Cleaner - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
- Open the left, rear door on the machine.
- Release two clips (1), and remove cover assembly (2) .
Show/hide table
 | |
| Illustration 1 | g00811622 |
- Remove primary element (3) .
Show/hide table
 | |
| Illustration 2 | g00811623 |
- Remove secondary element (4) .
Show/hide table
 | |
| Illustration 3 | g00811624 |
- Loosen two hose clamps (5), and remove hose (6). Disconnect two electrical connectors (7), and cut the tie strap for the wiring harness.
Show/hide table
 | |
| Illustration 4 | g00811625 |
- Loosen clamp (8), and remove bolts (9). Remove the air cleaner housing.
Show/hide table
 | |
| Illustration 5 | g00811629 |
- Remove seal (10) from the cover assembly.
Show/hide table
 | |
| Illustration 6 | g00811630 |
Installation Procedure
Note: Check the seal and hoses for wear and for damage. Replace the components, if necessary.
- Install seal (10) in the cover assembly.
Show/hide table
| | |
| Illustration 7 | g00811630 |
- Place the air cleaner housing in position on the machine. Install bolts (9) in order to fasten the air cleaner housing to the machine. Tighten clamp (8) .
Show/hide table
| | |
| Illustration 8 | g00811629 |
- Connect hose (6) to the air cleaner housing. Tighten clamp (5). Attach electrical connectors (7) .
Show/hide table
| | |
| Illustration 9 | g00811625 |
- Install secondary element (4) .
Show/hide table
| | |
| Illustration 10 | g00811624 |
- Install primary element (3) .
Show/hide table
| | |
| Illustration 11 | g00811623 |
- Install cover assembly (2), and engage clips (1) .
Show/hide table
| | |
| Illustration 12 | g00811622 |
- Close the left, rear door.
Information System:
HDB Series and M1 Series Heavy Duty Brushless Alternators
General Information
3064 and 3066 Engines for Caterpillar Built Machines
Low Idle RPM - Adjust
325C and 325C L Excavator
Hydraulic System Oil Filter (Pilot) - Replace
325C and 325C L Excavator
Hydraulic System Oil Filter (Case Drain) - Replace
Starting Motor Solenoid - Replace {1467}
325C Excavator
Fuses - Replace
325C and 325C L Excavator
Fuel System Filter - Replace
325C and 325C L Excavator
Engine Oil and Filter - Change
3064 and 3066 Engines for Caterpillar Built Machines
Fuel Injection Timing - Check
325C and 325C L Excavator
Engine Oil Level - Check
2002/05/06
New High Temperature Buffer Seals Reduce Oil Leakage From Hydraulic Cylinders {7562}
312C Excavator 3064 Engine Supplement
Turbocharger - Install
HDB Series and M1 Series Heavy Duty Brushless Alternators
Normal Operation
3064 and 3066 Engines for Caterpillar Built Machines
Engine Valve Lash - Inspect/Adjust
3064 and 3066 Engines for Caterpillar Built Machines
Engine Oil Pressure - Test
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System
Using Caterpillar Electronic Technician to Determine Diagnostic Codes
3064 and 3066 Engines for Caterpillar Built Machines
Cooling System - Test
3500B Engines for 5130B and 5230B Excavators
System Overview
5230B Excavator Electronic Systems Guide
Vital Information Management System (VIMS)
3500B Engines
Electronic Control Terms
2001/07/30
Correctly Assembling the Buffer Seal Will Prevent Failure of the U-Cup Seals {7562}
312C Excavator 3064 Engine Supplement
Water Pump - Remove
312C Excavator 3064 Engine Supplement
Water Pump - Install
Quick Coupler Wedge Lock(Wheel Loader)
Safety Signs and Labels