3064 and 3066 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install Caterpillar


Engine Oil Pressure Switch - Remove and Install
`
3064 and 3066 Engines for Caterpillar Built Machines [SENR5553]
ELECTRICAL AND STARTING SYSTEM
SWITCH GP
3064 and 3066 Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.


    Note: Disconnect all electrical connections to the engine oil pressure switch before proceeding. Mark all connections for later installation.




    Illustration 1g00815016

  1. Remove engine oil pressure switch (1) from the cylinder block.

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.





Illustration 2g00815016

  1. Install engine oil pressure switch (1) in the cylinder block.

  1. Tighten engine oil pressure switch (1) to a torque of 7 to 12 N·m (62 to 106 lb in).

    Note: Reconnect all electrical connections to the engine oil pressure switch before you operate the engine.

Information System:

3500B Engines Engine Oil Pressure is Low
3064 and 3066 Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install
5130B Excavator Engine Air Filter Service Indicator - Inspect
3500B Engines for 5130B and 5230B Excavators Power Shift Solenoid Circuit - Test
5230B Excavator Machine Electronic Control System Swing Brake Function
5130B Excavator Hydraulic System Oil Level - Check
M318 Excavator Hydraulic System General Testing and Adjusting Information
M312, M315, M318 and M320 Excavators Hydraulic System Relief Valve (Signal Limiter)
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Disassemble - M1 Series Alternator (35 Amp)
3500B Engines for 5130B and 5230B Excavators Injector Solenoids
3064 and 3066 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
5130B Excavator Swing Drive Oil - Change
5230B Excavator Machine Electronic Control System Travel Brake Function
5110B Excavator, 24H Motor Grader, 69D, 769D, 773D, 773E, 776D and 777D Off-Highway Truck/Tractors, 771D, 775D and 775E Quarry Trucks and AD40 Series II, AD45 and AE40 II Underground Articulated Trucks Caterpillar Monitoring System Using Caterpillar Monitoring System to Determine Diagnostic Codes
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Assemble - M1 Series Alternator (35 Amp)
5130B Excavator Bucket Link Pins - Lubricate
305 CR Mini Hydraulic Excavator Hydraulic System Main Hydraulic Pump Air - Purge
3500B Engines for 5130B and 5230B Excavators Starting Aid Lamp Circuit - Test
5110B Excavator, 24H Motor Grader, 69D, 769D, 773D, 773E, 776D and 777D Off-Highway Truck/Tractors, 771D, 775D and 775E Quarry Trucks and AD40 Series II, AD45 and AE40 II Underground Articulated Trucks Caterpillar Monitoring System Diagnostic Capabilities
5230B Excavator Machine Electronic Control System Dual Pressure Relief Function
3508 and 3516 EUI Engines for 5130 and 5230 Excavators Cat Data Link
5230B Excavator Machine Electronic Control System Automatic Engine Speed Control Function
5230B Excavator Hydraulic System Control Valve Spool Operation
HDB Series and M1 Series Heavy Duty Brushless Alternators Field Winding - Test