345B, 345B Series II and W345B Series II Excavators Engine Supplement Turbocharger - Install Caterpillar


Turbocharger - Install
`
345B, 345B Series II and W345B Series II Excavators Engine Supplement [RENR1043]
AIR INLET AND EXHAUST SYSTEM
TURBOCHARGER GP
345B, 345B Series II and W345B Series II Excavators Engine Supplement Turbocharger - Remove
345B, 345B Series II and W345B Series II Excavators Engine Supplement Turbocharger - Install
1.1. Installation Procedure

Installation Procedure




    Illustration 1g00663085

    Typical example

    Note: Replace all gaskets and replace all seals with new parts.

  1. Install a new turbocharger gasket. Install turbocharger (10). The weight of the turbocharger is 26 kg (57 lb).

  1. Apply 5P-3931 Anti-Seize Compound on the threads of all the bolts when you install the turbocharger on the manifold.

  1. Install four locknuts (6). Tighten the locknuts to a torque of 70 ± 15 N·m (52 ± 11 lb ft).

  1. Install the tube assembly on the bottom of the turbocharger.

  1. Connect turbocharger (10) to exhaust pipe (9). Tighten clamp (5) .

  1. Install hose (8). Tighten two clamps (7) .



    Illustration 2g00663082

  1. Connect three oil hoses (4) .



    Illustration 3g00663079

  1. Install elbow (3). Tighten clamp (1). Tighten hose clamp (2) .

  1. Install the heat shield on the turbocharger.

Information System:

W345B Series II Material Handler Hydraulic System Travel Counterbalance Valve
345B, 345B Series II and W345B Series II Excavators Engine Supplement Turbocharger - Remove
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators Operating Technique Information
325C Excavator Hydraulic System Fan Motor (Hydraulic Oil Cooler) - Test - Measurement of Case Drain Oil
5130B Excavator Capacities (Refill)
312C Excavator 3064 Engine Supplement Engine - Install
305.5 Mini Hydraulic Excavator Operation Information
2002/03/04 The Durability of the Coupling Gear in the Final Drive Is Improved {4055}
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators Engine and Machine Warm-Up
5230B Excavator Pump Drive Oil - Change
5230B Excavator Engine Oil and Filter - Change
5230B Excavator Engine Oil Level - Check
325C Excavator Hydraulic System Fan Motor Speed (Hydraulic Oil Cooler) - Test and Adjust
325C Excavator Hydraulic System Fan Motor Speed (Hydraulic Oil Cooler) - Test and Adjust
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Travel in Water and Mud
325C Excavator Hydraulic System Fan Motor (Hydraulic Oil Cooler) - Test - Measurement of Case Drain Oil
5230B Excavator Cooling System Relief Valve - Clean
5230B Excavator Cooling System Coolant Extender (ELC) - Add
5230B Excavator Cooling System Coolant (ELC) - Change
W345B Series II Material Handler Hydraulic System Cylinder (Boom, Stick and Grapple)
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Boom, Stick and Bucket Operation
2001/12/17 Correction to Service Magazine, "Improved 24 Volt Horns Available" {7402}
305.5 Mini Hydraulic Excavator Quick Coupler Operation - If Equipped
325C Excavator Hydraulic System Fan Motor (Hydraulic Oil Cooler) - Test - Measurement of Case Drain Oil