Alternator - Assemble - HDB Series Alternator
`
HDB Series and M1 Series Heavy Duty Brushless Alternators
[SENR4130]
HDB Series and M1 Series Heavy Duty Brushless Alternators
Charging System
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator - Disassemble - HDB Series Alternator
ELECTRICAL AND STARTING SYSTEM
ALTERNATOR GP-CHARGING
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator
HDB Series and M1 Series Heavy Duty Brushless Alternators
General Information
HDB Series and M1 Series Heavy Duty Brushless Alternators
Normal Operation
HDB Series and M1 Series Heavy Duty Brushless Alternators
Component Description
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator - Disassemble - M1 Series Alternator (35 Amp)
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator - Assemble - M1 Series Alternator (35 Amp)
HDB Series and M1 Series Heavy Duty Brushless Alternators
Field Winding - Test
1.1. Assembly Procedure
Assembly Procedure
Note: Before assembly, clean all parts in cleaning fluid. Allow the parts to air dry. DO NOT dry the parts with wiping cloths or with rags. Cloths and rags contain lint. Inspect all parts. Replace worn parts and replace damaged parts.
- Install ball bearing (28) into the front frame. The installation of this component requires force.
Show/hide table
![]() | |
Illustration 1 | g00825148 |
- Install retainer (27). Install three bolts (26) .
Show/hide table
![]() | |
Illustration 2 | g00825149 |
- Install spacer (25) onto the rotor.
Show/hide table
![]() | |
Illustration 3 | g00825154 |
- Install rotor (24) onto the front frame. The installation of this component requires force.
Show/hide table
![]() | |
Illustration 4 | g00825155 |
- Install stator (23) onto the front frame. Align the mark on the stator to the mark on the front frame.
Show/hide table
![]() | |
Illustration 5 | g00825156 |
- Install roller bearing (22) into the rear frame. The installation of this component requires force. Apply grease to the roller bearing, if necessary.
Show/hide table
![]() | |
Illustration 6 | g00825158 |
- Install field coil (21) onto the rear frame. The leads must fit through the rear frame. Install three bolts (20) .
Show/hide table
![]() | |
Illustration 7 | g00825168 |
- Attach rear frame (18) to front frame (19). Align the mark on the rear frame to the mark on the front frame. The stator leads must pass through the appropriate openings. Install four bolts (17) .
Show/hide table
![]() | |
Illustration 8 | g00825170 |
- Install rectifier (16). Install five bolts (14). Connect the stator leads to the rectifier and install four bolts (10). Tighten "B+" terminal (9) to the following torque: 18.2 ± 2.4 N·m (13.4 ± 1.8 lb ft)
Show/hide table
![]() | |
Illustration 9 | g00825173 |
- Install "R" terminal (12). Install grommet (11). Install bolt (13) .
- Install "B-" terminal (15). Tighten the "B-" bolt to the following torque: 4.4 ± 1 N·m (39 ± 9 lb in)
- Install regulator (8). Install the three bolts (7). Connect the field winding leads to the regulator. Install two bolts (6) .
Note: The regulator terminal that is closest to the "B+" terminal goes on top of the rectifier terminal. The regulator terminal that is farthest from the "B+" terminal goes underneath the rectifier terminal.
Show/hide table
![]() | |
Illustration 10 | g00825175 |
- Install the rear cover. Install three bolts (5) .
Show/hide table
![]() | |
Illustration 11 | g00825176 |
- Install spacer (4), fan (3), washer (1), and pulley nut (2) to the rotor shaft. Tighten the pulley nut to the following torque: 127 ± 10 N·m (94 ± 7 lb ft)
Show/hide table
![]() | |
Illustration 12 | g00825178 |
- Restore the residual magnetism in the alternator. Refer to Testing and Adjusting, "Residual Magnetism - Restore".
End By: Install the alternator on the machine. Refer to Disassembly and Assembly, "Alternator - Install" for the machine that is being serviced.
Information System:
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
Swing Lock Pin Control
312C Excavator Machine Systems
Fuel Tank - Remove
Procedure to Reinforce the Frame Assembly Stabilizer{7222}
325D and 329D Excavators and 325D Material Handler Machine System Specifications
Fasteners - Swing Drive and Final Drive
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers
Engine Temperature Sensor Open or Short Circuit - Test
312C Excavator Machine Systems
Accumulator - Remove and Install
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM
Attachment Code - Configure
5230B Excavator Vital Information Management System (VIMS)
Service Operations
5230B Excavator Vital Information Management System (VIMS)
Normal Operation
5230B Excavator Vital Information Management System (VIMS)
General Information
C-9 Engine for Caterpillar Built Machines
Engine Pressure Sensor Open or Short Circuit - Test
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators
Shipping the Machine
312C Excavator Machine Systems
Fuel Tank - Install
305 CR Mini Hydraulic Excavator
Access Door and Cover Locations
312C Excavator Machine Systems
Tank and Filter (Hydraulic) - Remove
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator - Disassemble - HDB Series Alternator
305 CR Mini Hydraulic Excavator
Capacities (Refill)
330B Excavator Machine System Specifications
Track Carrier Roller
416D, 420D, 424D, 428D, 430D, 432D and 442D Backhoe Loaders
Sound Information and Vibration Information
312C and 312C L Excavator
Plate Locations and Film Locations
305 CR Mini Hydraulic Excavator
Belt - Inspect/Adjust/Replace
2001/10/15
A Correction to Spacers for Installing Tire Chains on the Rear Wheels of Backhoe Loaders Are Now Available {3259, 3278, 4201}
420D and 430D Backhoe Loaders
Quick Coupler Control (Loader) - If Equipped
420D and 430D Backhoe Loaders
Quick Coupler Operation (Loader)