336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Crankshaft Vibration Damper and Pulley - Remove and Install Caterpillar


Crankshaft Vibration Damper and Pulley - Remove and Install
`
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement [KENR8156]
BASIC ENGINE
DAMPER GP
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Crankshaft Vibration Damper and Pulley - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
FT-2515  Guide Stud 
Loctite 242 


    Illustration 1g02178960

  1. Remove bolts (1) and plate assembly (2).


    Illustration 2g02144165


    Illustration 3g02144168

  2. Remove belts (5). Refer to Operation and Maintenance Manual, "Belt - Inspect/Adjust/Replace".

  3. Remove one bolt (7) and install Tooling (A).

  4. Remove the remaining bolts (7), pulley (6), damper (4), and pulley (3).

  5. Remove Tooling (A).


    Illustration 4g02184953

  6. Remove bolts (9), washer (10), and adapter (8).

Installation Procedure

  1. Install the crankshaft vibration damper and pulley in the reverse order of removal.

    1. Tighten bolts (9) to a torque of 200 ± 25 N·m (150 ± 18 lb ft).

    2. Apply Tooling (B) to the threads of bolts (1).

Information System:

336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Water Pump - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Bucket Linkage - Remove and Install
349F and 352F Excavators Hydraulic System Relief Valve (Swing) - Test and Adjust
Installation of the 260-7976 Pilot Lines Gp on Certain 320Dand 323D Excavators{5057, 5059}
C13 Engines for Caterpillar Built Machines Exhaust Combustion Lines
2013/08/29 Data for the Engine and Power Train for Series E Backhoe Loaders {0374, 1000, 3101, 7000}
374D Excavator Plate Locations and Film Locations
Removal and Installation of Unit Injectors on 3114, 3116, and 3126 MUI Engines{1251, 1290}
349F and 352F Excavators Hydraulic System Relief Valve (Line) - Test and Adjust
349E Excavator Hydraulic System Swing Hydraulic System
349F and 352F Excavators Hydraulic System Pump Control (Main Hydraulic) - Main Pump Regulator
374D Excavator Leaving the Machine
568 Forest Machine Hydraulic System Relief Valve (Line) - Test and Adjust
568 Forest Machine Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
568 Forest Machine Hydraulic System Relief Valve (Swing) - Test and Adjust
568 Forest Machine Hydraulic System Specifications
Installation of the 281-8245 Auxiliary Hydraulic Lines Gp on Certain Hydraulic Excavators {5057, 5057}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Crankshaft Front Seal - Remove and Install
330D and 336D Excavators and 336D Mobile Hydraulic Power Units Maintenance Interval Schedule
568 Forest Machine Hydraulic System Operational Checks
568 Forest Machine Hydraulic System Travel on Level Ground - Test
568 Forest Machine Hydraulic System Travel on Level Ground - Test - Optional Test
568 Forest Machine Hydraulic System Swing Speed and Overswing on Level Ground - Check
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735B, 735C, 740B, 740B Ejector, 740C Ejector and 745C Articulated Trucks VIMSTM 3G Electrical Connector - Inspect