VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Swivel - Assemble Caterpillar


Swivel - Assemble
`
1.1. Assembly Procedure

Assembly Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


Cleanliness is an important factor. Before assembly, all parts should be cleaned thoroughly in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause damage after prolonged operation. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.

  1. Clean all parts and inspect all parts. If any parts are worn or damaged, use new parts for replacement.



    Illustration 1g00707860

  1. Install three seal assemblies (8) to the rotor.

  1. Install two seals (7) and 2 rings (6). There is a ring and a seal at each end of the rotor.

  1. Lubricate the sealing lips of the seals with clean hydraulic oil.



    Illustration 2g00707854

  1. Use a hydraulic press or a rubber mallet to install rotor (5) onto stator (4). Use care when you assemble the swivel in order to avoid damage to the seals.



    Illustration 3g00707270

  1. Place ring (2) and locking plate (1) into position on swivel (3). Apply 4C-9506 Retaining Compound to the threads of the three bolts that secure the plate and the ring. Install the bolts and stake the tabs of the locking plate against the bolts.

End By: Install the swivel to the work tool.

Information System:

336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Engine and Main Hydraulic Pump - Remove and Install
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Hydraulic Rotator and Hydraulic Crusher Housing - Separate
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Speed Control Valve - Disassemble
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Hydraulic Cylinder - Remove and Install
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Hydraulic Cylinder - Remove and Install
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Swivel - Remove and Install
2010/04/30 A Rework Procedure Improves the Seal Assembly Performance in Hydraulic Cylinders on Cat Products {7562}
C9.3 Tier 4 Final Engines Diesel Particulate Filter Has Changed Regeneration Interval
MP15, MP20, MP30 and MP40 Multi-Processors Operation
374D Excavator Machine System Specifications Bucket Linkage - WB Family
Installation and Operation of the Caterpillar Diesel Particulate Filter (DPF) and the Diagnostic Module for Non-Road Machine Applications (Non-California Applications) {108F, 1091, 7490}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Engine Rear Mount - Remove and Install
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Gerotor Motor - Assemble
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Gerotor Motor - Disassemble
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Swivel - Disassemble
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Speed Control - Remove and Install
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Hydraulic Cylinder - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick Cylinder - Remove and Install
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Crusher Tooth - Remove and Install
349E Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
VHC-30, VHC-40, VHC-50 and VHC-60 Hydraulic Crushers Ripper Tooth - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Fuel Filter and Water Separator Base - Remove and Install
317-7492 Wireless Radio{7338}