Fuel Injection Pump Gear - Remove
`
C6.6 Industrial Engine
[KENR9110]
C6.6 Industrial Engine
Fuel Injection Pump - Install
C6.6 Industrial Engine
Fuel Injection Pump Gear - Install
1.1. Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Puller (Two Legged) | 1 |
| B | - | E10 Torx Socket 1/4" Square Drive |
1 |
Start By:
- Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
- Use a suitable tool in order to prevent fuel injection pump gear (3) from rotating.
Note: Do not use timing pin for the fuel injection in order to prevent the fuel injection pump gear from rotating.
- Remove nut (1) and washer (2).
- Use Tooling (A) in order to remove gear (3) from the shaft of fuel injection pump (7).
- Remove key (6) from the shaft of fuel injection pump (7).
- Use Tooling (B) in order to remove Torx screws (8) and the washers.
- Remove adapter plate (4) from fuel injection pump (7).
- Remove O-ring seal (5).
Show/hide table
| |
| Illustration 1 | g01970674 |
Information System:
C6.6 Industrial Engine
Fuel Injection Pump - Install
C6.6 Industrial Engine
Fuel Injection Pump - Remove
C6.6 Industrial Engine
Inlet Air Control - Install - NRS Inlet Air Mixer
C6.6 Industrial Engine
Inlet Air Control - Remove - NRS Inlet Air Mixer
C6.6 Industrial Engine
Fuel Injection Lines - Install
C6.6 Industrial Engine
Fuel Injection Lines - Remove
C6.6 Industrial Engine
Fuel Manifold (Rail) - Remove and Install
C6.6 Industrial Engine
Fuel Filter Base - Remove and Install - Single Secondary Fuel Filter
C6.6 Industrial Engine
Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
374F Excavator Machine System
Grease Lines
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Fuel Transfer and Priming Pump - Remove and Install
349F and 352F Excavators Hydraulic System
Pump Control (Negative Flow) - Test
C7.1 Industrial Engine
Position the Valve Mechanism Before Maintenance Procedures
C4.4 Industrial Engine
Position the Valve Mechanism Before Maintenance Procedures
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Fuel Shutoff Solenoid - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Engine Oil Filter and Oil Filter Base - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Fan - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Engine Oil Cooler - Remove and Install
303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement
Hood - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Refrigerant Condenser - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Water Temperature Regulator - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Refrigerant Compressor - Remove and Install
2010/05/17
The Relay Switch for the Heater has been Relocated to Improve the Reliability of the Switch on Certain Excavators {1417}
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Refrigerant Receiver-Dryer - Remove and Install