303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Fuel Shutoff Solenoid - Remove and Install Caterpillar


Fuel Shutoff Solenoid - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.





    Illustration 1g01223493

  1. Open access door (1) .



    Illustration 2g02149747

  1. Remove bolts (3) and access panel (2) .



    Illustration 3g01223513

  1. Disconnect harness assembly (6). Remove nuts (4) and fuel shutoff solenoid (5) .

Installation Procedure




    Illustration 4g01223513

  1. Position fuel shutoff solenoid (5) and install nuts (4). Connect harness assembly (6).



    Illustration 5g02149747

  1. Position access panel (2) and install bolts (3) .



    Illustration 6g01223493

  1. Close access door (1) .

Information System:

C4.4 Industrial Engine Position the Valve Mechanism Before Maintenance Procedures
C7.1 Industrial Engine Position the Valve Mechanism Before Maintenance Procedures
C6.6 Industrial Engine Fuel Injection Pump Gear - Remove
C6.6 Industrial Engine Fuel Injection Pump - Install
C6.6 Industrial Engine Fuel Injection Pump - Remove
C6.6 Industrial Engine Inlet Air Control - Install - NRS Inlet Air Mixer
C6.6 Industrial Engine Inlet Air Control - Remove - NRS Inlet Air Mixer
C6.6 Industrial Engine Fuel Injection Lines - Install
C6.6 Industrial Engine Fuel Injection Lines - Remove
C6.6 Industrial Engine Fuel Manifold (Rail) - Remove and Install
C6.6 Industrial Engine Fuel Filter Base - Remove and Install - Single Secondary Fuel Filter
C6.6 Industrial Engine Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Fan - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Engine Oil Cooler - Remove and Install
303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement Hood - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Condenser - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Water Temperature Regulator - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Compressor - Remove and Install
2010/05/17 The Relay Switch for the Heater has been Relocated to Improve the Reliability of the Switch on Certain Excavators {1417}
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
349E Excavator Hydraulic System Gear Pump (Pilot) - Test
2010/04/30 The Pin Assembly and Pin Retention Is Improved on Certain Bucket Arrangements for the 385C Excavator {6068, 7562}
MP15, MP20, MP30 and MP40 Multi-Processors Transport Position