Engine Oil Filter and Oil Filter Base - Remove and Install
`
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
[UENR0101]
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Fuel Shutoff Solenoid - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Fan - Remove and Install
LUBRICATION SYSTEM
FILTER GP-ENGINE OIL
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Engine Oil Filter and Oil Filter Base - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 185-3630     | Strap Wrench As     | 1     |
- Open the engine door.
- Use Tooling (A) in order to remove engine oil filter (5). Disconnect hose assemblies (2) and (3). Remove bolts (1) and oil filter base (4) .
Show/hide table
Illustration 1 | g01221378 |
Installation Procedure
- Position oil filter base (4) and install bolts (1). Connect hose assemblies (2) and (3). Install engine oil filter (5) .
Show/hide table
Illustration 2 | g01221378 |
- Check the level of the engine oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check".
Information System:
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Fuel Shutoff Solenoid - Remove and Install
C4.4 Industrial Engine
Position the Valve Mechanism Before Maintenance Procedures
C7.1 Industrial Engine
Position the Valve Mechanism Before Maintenance Procedures
C6.6 Industrial Engine
Fuel Injection Pump Gear - Remove
C6.6 Industrial Engine
Fuel Injection Pump - Install
C6.6 Industrial Engine
Fuel Injection Pump - Remove
C6.6 Industrial Engine
Inlet Air Control - Install - NRS Inlet Air Mixer
C6.6 Industrial Engine
Inlet Air Control - Remove - NRS Inlet Air Mixer
C6.6 Industrial Engine
Fuel Injection Lines - Install
C6.6 Industrial Engine
Fuel Injection Lines - Remove
C6.6 Industrial Engine
Fuel Manifold (Rail) - Remove and Install
C6.6 Industrial Engine
Fuel Filter Base - Remove and Install - Single Secondary Fuel Filter
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Fan - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Engine Oil Cooler - Remove and Install
303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement
Hood - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Refrigerant Condenser - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Water Temperature Regulator - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Refrigerant Compressor - Remove and Install
2010/05/17
The Relay Switch for the Heater has been Relocated to Improve the Reliability of the Switch on Certain Excavators {1417}
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement
Refrigerant Receiver-Dryer - Remove and Install
349E Excavator Hydraulic System
Gear Pump (Pilot) - Test
2010/04/30
The Pin Assembly and Pin Retention Is Improved on Certain Bucket Arrangements for the 385C Excavator {6068, 7562}
MP15, MP20, MP30 and MP40 Multi-Processors
Transport Position
MP15, MP20, MP30 and MP40 Multi-Processors
Shipping