303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement Hood - Remove and Install Caterpillar


Hood - Remove and Install
`
303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement [UENR5591]
FRAME AND BODY
HOOD GP
303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement Hood - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure



    Illustration 1g01221488

  1. Open hood (1). Attach a suitable lifting device to hood (1). The weight of hood (1) is approximately 23 kg (50 lb).

    ------ WARNING! ------

    Personal injury can result from being struck by parts propelled by a released spring force.

    Make sure to wear all necessary protective equipment.

    Follow the recommended procedure and use all recommended tooling to release the spring force.


  2. Disconnect strut (4) from hood (1). Remove bolts (2) from each hinge assembly (3). Remove hood (1). Remove any shims that may be present.

Installation Procedure



    Illustration 2g01221488

  1. Attach a suitable lifting device to hood (1). The weight of hood (1) is approximately 23 kg (50 lb). Position hood (1). Install any shims that were present during the removal procedure. Install bolts (2) for each hinge assembly (3).

    ------ WARNING! ------

    Improper assembly of parts that are spring loaded can cause bodily injury.

    To prevent possible injury, follow the established assembly procedure and wear protective equipment.


  2. Connect strut (4) to hood (1). Close hood (1).

Information System:

303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Engine Oil Cooler - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Fan - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Fuel Shutoff Solenoid - Remove and Install
C4.4 Industrial Engine Position the Valve Mechanism Before Maintenance Procedures
C7.1 Industrial Engine Position the Valve Mechanism Before Maintenance Procedures
C6.6 Industrial Engine Fuel Injection Pump Gear - Remove
C6.6 Industrial Engine Fuel Injection Pump - Install
C6.6 Industrial Engine Fuel Injection Pump - Remove
C6.6 Industrial Engine Inlet Air Control - Install - NRS Inlet Air Mixer
C6.6 Industrial Engine Inlet Air Control - Remove - NRS Inlet Air Mixer
C6.6 Industrial Engine Fuel Injection Lines - Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Condenser - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Water Temperature Regulator - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Compressor - Remove and Install
2010/05/17 The Relay Switch for the Heater has been Relocated to Improve the Reliability of the Switch on Certain Excavators {1417}
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
349E Excavator Hydraulic System Gear Pump (Pilot) - Test
2010/04/30 The Pin Assembly and Pin Retention Is Improved on Certain Bucket Arrangements for the 385C Excavator {6068, 7562}
MP15, MP20, MP30 and MP40 Multi-Processors Transport Position
MP15, MP20, MP30 and MP40 Multi-Processors Shipping
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick Bearings and Seals - Remove and Install
C6.6 Industrial Engine Fuel Injection Pump Gear - Install
C6.6 Industrial Engine Electronic Unit Injector - Remove