C6.6 Industrial Engine Fuel Injection Pump Gear - Install Caterpillar


Fuel Injection Pump Gear - Install
`
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
E10 Torx Socket
1/4" Square Drive 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Ensure that the fuel injection pump gear is clean and free from wear of damage. If necessary, replace the fuel pump gear. Ensure that the shaft for the fuel injection pump is clean and free from wear or damage.


    Illustration 1g01970674

  2. Position a new O-ring seal (5) onto fuel injection pump (7).

  3. Position adapter plate (4) onto fuel injection pump (7).

  4. Install new Torx screws (8) and washers.

  5. Use Tooling (B) in order to tighten Torx screws (8) to a torque of 22 N·m (195 lb in).

  6. Install key (6) to the shaft of fuel injection pump (7).

  7. Position gear (3) from the shaft of fuel injection pump (7).

  8. Position a new washer (2) onto the shaft of the fuel injection pump. Install nut (1) and tighten the nut hand tight.

  9. Use a suitable tool in order to prevent fuel injection pump gear (3) from rotating.

    Note: Do not use timing pin for the fuel injection in order to prevent the fuel injection pump gear from rotating.

  10. Tighten nut (1) to a torque of 64 N·m (47 lb ft).

End By:

  1. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install".

Information System:

336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick Bearings and Seals - Remove and Install
MP15, MP20, MP30 and MP40 Multi-Processors Shipping
MP15, MP20, MP30 and MP40 Multi-Processors Transport Position
2010/04/30 The Pin Assembly and Pin Retention Is Improved on Certain Bucket Arrangements for the 385C Excavator {6068, 7562}
349E Excavator Hydraulic System Gear Pump (Pilot) - Test
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
2010/05/17 The Relay Switch for the Heater has been Relocated to Improve the Reliability of the Switch on Certain Excavators {1417}
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Compressor - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Water Temperature Regulator - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Condenser - Remove and Install
303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement Hood - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Engine Oil Cooler - Remove and Install
C6.6 Industrial Engine Electronic Unit Injector - Remove
C6.6 Industrial Engine Electronic Unit Injector - Install
C6.6 Industrial Engine Wastegate Solenoid - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C6.6 Industrial Engine Engine Oil Filter Base - Remove and Install
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Pump - Remove
C6.6 Industrial Engine Engine Oil Pump - Install