C6.6 Industrial Engine Engine Oil Filter Base - Remove and Install Caterpillar


Engine Oil Filter Base - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
1U-8760  Chain Wrench 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g01980935

  1. Place a suitable container below engine oil filter (5) in order to catch any oil that might be spilled.

  2. Use Tooling (A) to remove engine oil filter (5). Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.

  3. Remove bolts (3).

    Note: If bolts of different lengths are installed, identify the correct position of the bolts.

  4. Remove engine oil filter base (4).

  5. Remove gasket (6).

  6. If necessary, remove plug (1) from engine oil filter base (4). Remove O-ring seal (2) from plug (1).

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 2g01980935

  1. Clean engine oil filter base (4). Clean the gasket surfaces of the cylinder block or the engine oil cooler.

  2. If necessary, install new O-ring seal (2) to plug (1). Install plug (1) to engine oil filter base (4). Tighten the plug to a torque of 12 N·m (106 lb in).

  3. Install bolts (3) to engine oil filter base (4).

  4. Install a gasket (6) onto bolts (3). Install the assembly of the engine oil filter base to the cylinder block or the engine oil cooler.

  5. Tighten bolts (3) to a torque of 22 N·m (195 lb in).

  6. Install a new engine oil filter (5) and check the level of the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure.

Information System:

C6.6 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Industrial Engine Wastegate Solenoid - Remove and Install
C6.6 Industrial Engine Electronic Unit Injector - Install
C6.6 Industrial Engine Electronic Unit Injector - Remove
C6.6 Industrial Engine Fuel Injection Pump Gear - Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick Bearings and Seals - Remove and Install
MP15, MP20, MP30 and MP40 Multi-Processors Shipping
MP15, MP20, MP30 and MP40 Multi-Processors Transport Position
2010/04/30 The Pin Assembly and Pin Retention Is Improved on Certain Bucket Arrangements for the 385C Excavator {6068, 7562}
349E Excavator Hydraulic System Gear Pump (Pilot) - Test
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Pump - Remove
C6.6 Industrial Engine Engine Oil Pump - Install
C6.6 Industrial Engine Water Pump - Remove
C6.6 Industrial Engine Water Pump - Install
C6.6 Industrial Engine Water Temperature Regulator - Remove and Install
C6.6 Industrial Engine Flywheel - Remove
C6.6 Industrial Engine Flywheel - Install
C6.6 Industrial Engine Crankshaft Rear Seal - Remove