C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base Caterpillar


Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
`
1.1. Removal Procedure

Removal Procedure

Start By:

  1. Remove the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.


NOTICE

Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.

Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.

Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.



NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Dispose of all fluids according to local regulations and mandates.


  1. Drain the coolant from the cooling system into a suitable container. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Drain" for the correct procedure.


    Illustration 1g02191813

  2. If the engine has a left-hand side oil filter, remove the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install" for the correct procedure.

    If the engine has a right-hand side oil filter, follow Step 2.a through Step 2.c in order to remove blanking plate (8).

    1. Remove bolts (10).

    2. Remove blanking plate (8).

    3. Remove gasket (9) (not shown).

  3. Remove bolt (1) from fuel injection line clamp (2). Position clamp (2) away from the engine oil cooler assembly.

  4. Cut cable straps (3) from the engine wiring harness assembly.

  5. Remove plastic tube assembly (4) from crankcase breather canister (5) and the plastic tube assembly clips.

  6. Remove plastic tube assembly (12) from crankcase breather canister (5) and crankcase breather valve (11).

  7. Remove bolt (7) from bracket (6). Position bracket (6) away from the engine oil cooler.


    Illustration 2g02191874

  8. Do not remove bolts in Position (A).

  9. Remove bolts (13) from engine oil cooler (14).

    Note: The bolts are different lengths. Note the position of the different bolts. Note the location and the orientation of the brackets for the tube assemblies.

  10. Remove engine oil cooler assembly (14) from the cylinder block.

  11. Remove gasket (15) (not shown) from engine oil cooler (14).


    Illustration 3g02191814

  12. If necessary, follow Step 12.a through Step 12.c in order to disassembly the engine oil cooler.

    1. Remove bolts (16) from engine oil cooler assembly (14).

    2. Remove engine oil cooler matrix (19) from spacer plate (17).

    3. Remove gasket (18).

Information System:

C6.6 Industrial Engine Engine Oil Filter Base - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Industrial Engine Wastegate Solenoid - Remove and Install
C6.6 Industrial Engine Electronic Unit Injector - Install
C6.6 Industrial Engine Electronic Unit Injector - Remove
C6.6 Industrial Engine Fuel Injection Pump Gear - Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick Bearings and Seals - Remove and Install
MP15, MP20, MP30 and MP40 Multi-Processors Shipping
MP15, MP20, MP30 and MP40 Multi-Processors Transport Position
2010/04/30 The Pin Assembly and Pin Retention Is Improved on Certain Bucket Arrangements for the 385C Excavator {6068, 7562}
349E Excavator Hydraulic System Gear Pump (Pilot) - Test
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Pump - Remove
C6.6 Industrial Engine Engine Oil Pump - Install
C6.6 Industrial Engine Water Pump - Remove
C6.6 Industrial Engine Water Pump - Install
C6.6 Industrial Engine Water Temperature Regulator - Remove and Install
C6.6 Industrial Engine Flywheel - Remove
C6.6 Industrial Engine Flywheel - Install
C6.6 Industrial Engine Crankshaft Rear Seal - Remove
C6.6 Industrial Engine Crankshaft Rear Seal - Install