C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base Caterpillar


Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
`
1.1. Assembly Procedure

Assembly Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
Guide Stud
M8 by 50 mm 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Ensure that the wiring harness is correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.




    Illustration 1g02191814

  1. If necessary, follow Step 1.a through Step 1.d in order to assembly the engine oil cooler.

    1. Ensure that engine oil cooler matrix (19) is clean, free from damage and restriction. Replace engine oil cooler matrix (19) if damaged or restricted.

    2. Ensure that spacer plate (17) is clean and free from damage. Replace spacer plate (17) if damaged.

    3. Position a new gasket (18) onto spacer plate (17). Install engine oil cooler matrix (19) to the spacer plate.

    4. Install bolts (16) finger tight.


    Illustration 2g02192853


    Illustration 3g02192893
    Tightening sequence for an engine oil cooler with a blanking plate or with a low mounted oil filter base

  2. Clean the gasket surfaces of the cylinder block.

  3. Install Tooling (A) into Position (B).

  4. Position a new gasket (15) (not shown) onto Tooling (A).

  5. Install the assembly of engine oil cooler (14) to the cylinder block.

  6. Install bolts (13) to engine oil cooler (14).

    Note: Ensure that the bolts of different lengths are installed in the correct position. Ensure that any brackets for the tube assemblies are location and correctly orientated.

  7. Tighten bolts (13) and bolts (16) to a torque of 22 N·m (195 lb in) in the sequence that is shown in Illustration 3.

  8. Remove Tooling (A).


    Illustration 4g02191813

  9. If the engine has a low mounted oil filter on the left-hand side, install the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install" for the correct procedure.

    If the engine has a right-hand side oil filter, follow Step 9.a through Step 9.d in order to install blanking plate (8).

    1. Install bolts (10) to blanking plate (8).

    2. Position a new gasket (9) (not shown) onto blanking plate (8).

    3. Install the assembly of blanking plate (8) to the assembly of the engine oil cooler.

    4. Tighten bolts (10) to a torque of 22 N·m (195 lb in).

  10. Position bracket (6) onto engine oil cooler. Install bolt (7). Tighten bolts (7) to a torque of 22 N·m (195 lb in).

    Note: Ensure that locating pin for the bracket is correctly located into the engine oil cooler.

  11. Install bolt (1) to fuel injection line clamp (2). Tighten bolts (1) to a torque of 10 N·m (88 lb in).

  12. Install new cable straps (3) to the engine wiring harness assembly.

  13. Install plastic tube assembly (4) to crankcase breather canister (5) and to the plastic tube assembly clips.

  14. Install plastic tube assembly (12) to crankcase breather canister (5) and crankcase breather valve (11).

  15. Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.

  16. Check the level of the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure.

End By:

  1. Install the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.

Information System:

C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Filter Base - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Industrial Engine Wastegate Solenoid - Remove and Install
C6.6 Industrial Engine Electronic Unit Injector - Install
C6.6 Industrial Engine Electronic Unit Injector - Remove
C6.6 Industrial Engine Fuel Injection Pump Gear - Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick Bearings and Seals - Remove and Install
MP15, MP20, MP30 and MP40 Multi-Processors Shipping
MP15, MP20, MP30 and MP40 Multi-Processors Transport Position
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Pump - Remove
C6.6 Industrial Engine Engine Oil Pump - Install
C6.6 Industrial Engine Water Pump - Remove
C6.6 Industrial Engine Water Pump - Install
C6.6 Industrial Engine Water Temperature Regulator - Remove and Install
C6.6 Industrial Engine Flywheel - Remove
C6.6 Industrial Engine Flywheel - Install
C6.6 Industrial Engine Crankshaft Rear Seal - Remove
C6.6 Industrial Engine Crankshaft Rear Seal - Install
C6.6 Industrial Engine Flywheel Housing - Remove and Install - Standard Housing
349E Excavator Hydraulic System Return Hydraulic System