C6.6 Industrial Engine Engine Oil Pump - Install Caterpillar


Engine Oil Pump - Install
`
1.1. Installation Procedure

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

If any part of the engine oil pump is worn or damaged, the complete assembly of the engine oil pump must be replaced.


  1. Ensure that all components of the engine oil pump are clean and free from wear and damage. Refer to System Operation, Testing and Adjusting, "Engine Oil Pump - Inspect" for more information. Replace the complete assembly of the engine oil pump if any of the components are worn or damaged.


    Illustration 1g02429861


    Illustration 2g02429917

  2. If necessary, lubricate the internal components for the assembly of the engine oil pump with clean engine oil. Install outer rotor (10) and front cover (9) to the housing of engine oil pump (8). Install bolts (13). Tighten the bolts to a torque of 22 N·m (195 lb in).

  3. Ensure that two dowel (11) and dowel (12) are correctly located in the housing of engine oil pump (8). Position the assembly of the engine oil pump onto the cylinder block.

    Note: Ensure that the dowels in the housing of the engine oil pump are aligned with the holes in the cylinder block.

  4. Install bolts (7). Tighten the bolts to a torque of 22 N·m (195 lb in).

  5. Check the backlash between idler gear and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for further information.

  6. Install suction pipe (1) and a new gasket (6) (not shown) to the assembly of engine oil pump (9).

  7. Install bolts (5). Tighten the bolts to a torque to 22 N·m (195 lb in).

  8. If suction pipe (1) has a support bracket, follow Step 8.a through Step 8.d.

    1. Install the components of support bracket (3). Ensure the correct location and orientation of the bracket and the retaining clip.

    2. Install bolt (4).

    3. Tighten bolt (4) and bolt (2) finger tight in order to align the components of the support bracket.

    4. Tighten bolt (2) to a torque of 22 N·m (195 lb in).

      Tighten bolt (4) to a torque of 44 N·m (32 lb ft).

End By:

  1. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install" for the correct procedure.

Information System:

C6.6 Industrial Engine Engine Oil Pump - Remove
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Filter Base - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Industrial Engine Wastegate Solenoid - Remove and Install
C6.6 Industrial Engine Electronic Unit Injector - Install
C6.6 Industrial Engine Electronic Unit Injector - Remove
C6.6 Industrial Engine Fuel Injection Pump Gear - Install
C6.6 Industrial Engine Water Pump - Remove
C6.6 Industrial Engine Water Pump - Install
C6.6 Industrial Engine Water Temperature Regulator - Remove and Install
C6.6 Industrial Engine Flywheel - Remove
C6.6 Industrial Engine Flywheel - Install
C6.6 Industrial Engine Crankshaft Rear Seal - Remove
C6.6 Industrial Engine Crankshaft Rear Seal - Install
C6.6 Industrial Engine Flywheel Housing - Remove and Install - Standard Housing
349E Excavator Hydraulic System Return Hydraulic System
C9.3 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
MP15, MP20, MP30 and MP40 Multi-Processors Bushings - Lubricate
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Gear - Lubricate