C9.3 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install Caterpillar


Inlet Manifold - Remove and Install
`
C9.3 Engines for Caterpillar Built Machines [UENR0130]
AIR INLET AND EXHAUST SYSTEM
MANIFOLD GP-INLET
C9.3 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
A  −  Loctite Sealant − Gasket 

Start By:

  1. Remove the fumes disposal group.

  2. Remove the wastegate solenoid.


    Illustration 1g02150327

  1. Remove nut (1). Remove cable straps (2) Disconnect harness assemblies (3). Remove clamp (4).


    Illustration 2g02150381

  2. Remove bolts (5) and remove inlet manifold (6).


    Illustration 3g02150389

  3. Remove clamp (7). Remove bolts (8) and bolts (9). Separate inlet manifold (6) from elbow (11). Separate tube assembly (10) from elbow (11).


    Illustration 4g02150420

  4. Remove O-ring seal (12), wave ring (13), and tube (14).

Installation Procedure

  1. Install inlet manifold (6) in the reverse order of removal.

    1. Apply Tooling (A) uniformly to the face of inlet manifold (6) and assemble within 10 minutes of application.

Information System:

336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick - Remove and Install
Improved Jacket Water Circuit Breaker for Certain Electric Power Generators and Work Tools{1383, 1417, 1420}
MP15, MP20, MP30 and MP40 Multi-Processors Cutting Edges - Inspect/Replace
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Gear - Lubricate
MP15, MP20, MP30 and MP40 Multi-Processors Bushings - Lubricate
C9.3 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
349E Excavator Hydraulic System Return Hydraulic System
C6.6 Industrial Engine Flywheel Housing - Remove and Install - Standard Housing
C6.6 Industrial Engine Crankshaft Rear Seal - Install
C6.6 Industrial Engine Crankshaft Rear Seal - Remove
C6.6 Industrial Engine Flywheel - Install
C6.6 Industrial Engine Flywheel - Remove
2010/05/20 An Improved Hydraulic Tank is Available for Certain Excavators {5056}
2010/05/06 Improved Remanufactured Injectors Are Now Used on Some 3408E and 3412E Machine Engines {1251, 1254, 1290, 1713}
C13 Tier 4 Final Engines Exhaust Cooler (NRS) - Clean
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
C15 and C18 Tier 4 Final Engines Exhaust Cooler (NRS) - Test
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Inspect
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Inspect
MP15, MP20, MP30 and MP40 Multi-Processors Wear Plates - Inspect/Replace
C6.6 Industrial Engine Vibration Damper and Pulley - Remove
C6.6 Industrial Engine Vibration Damper and Pulley - Install