C6.6 Industrial Engine Vibration Damper and Pulley - Remove Caterpillar


Vibration Damper and Pulley - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     -     Guide Stud
M14 x 1.5 by 100 mm    
1    
B     227-4393     E18 Torx Socket     1    

Start By:

  1. Remove the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove and Install" for the correct procedure.

Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the crankshaft adapter is approximately 20 kg (44 lb).




    Illustration 1g02458316

  1. Use a suitable tool in order to prevent the crankshaft from rotating. Use Tooling (B) to remove one Torx screw (1) from crankshaft pulley assembly (2) .

  1. Install Tooling (A) into crankshaft pulley assembly (2) .

  1. Remove remaining Torx screws (1) from crankshaft pulley assembly (2) .

  1. Remove crankshaft pulley assembly (2) .

  1. Remove Tooling (A) .



    Illustration 2g02368018

  1. If necessary, follow Step 6.a through Step 6.b in order to remove friction shim (3) from the crankshaft.

    1. Remove the front seal from the front cover. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove and Install" for the correct procedure.

    1. Remove friction shim (3) .

  1. If necessary, follow Step 7.a through Step 7.c in order to disassemble vibration damper, crankshaft pulley from crankshaft adapter.

    1. Place the crankshaft pulley assembly onto a suitable support.

    1. Remove bolts (7) from crankshaft pulley assembly (2) .

    1. Remove vibration damper (6) and crankshaft pulley (5) from adapter (4) .

Information System:

MP15, MP20, MP30 and MP40 Multi-Processors Wear Plates - Inspect/Replace
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Inspect
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Inspect
C15 and C18 Tier 4 Final Engines Exhaust Cooler (NRS) - Test
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
C13 Tier 4 Final Engines Exhaust Cooler (NRS) - Clean
2010/05/06 Improved Remanufactured Injectors Are Now Used on Some 3408E and 3412E Machine Engines {1251, 1254, 1290, 1713}
2010/05/20 An Improved Hydraulic Tank is Available for Certain Excavators {5056}
C9.3 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick - Remove and Install
C6.6 Industrial Engine Vibration Damper and Pulley - Install
C4.4 Industrial Engine Engine Oil Pump
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C6.6 Industrial Engine Gear Group (Front) - Remove and Install
C6.6 Industrial Engine Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C6.6 Industrial Engine Idler Gear - Remove
C6.6 Industrial Engine Idler Gear - Install
C6.6 Industrial Engine Housing (Front) - Remove
C6.6 Industrial Engine Housing (Front) - Remove - Heavy Duty Housing (Front)
2010/05/13 The Gas Strut on Backhoe Loader Steering Columns Has Been Improved {4309, 4310, 4338}
C6.6 Industrial Engine Housing (Front) - Install