C6.6 Industrial Engine Vibration Damper and Pulley - Install Caterpillar


Vibration Damper and Pulley - Install
`
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     -     Guide Stud
M14 x1.5 by 100 mm    
1    
B     227-4393     E18 Torx Socket     1    
C     8T-3052     Degree Wheel     1    
D     -     Guide Stud
M12 x1.75 by 50 mm    
2    


NOTICE

Do not lubricate the crankshaft front seal. The crankshaft front seal must be installed dry.



NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.





    Illustration 1g02368018

  1. Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from damage.

  1. Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.

  1. If necessary, follow Step 3.a through Step 3.e in order to install vibration damper, crankshaft pulley to crankshaft adapter.

    1. Place crankshaft adapter (4) onto a suitable support.

    1. Install Tooling (D) crankshaft adapter (4) .

    1. Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .

    1. Install bolts (7) to the crankshaft pulley assembly.

      Note: Evenly space bolts (7) around the crankshaft pulley assembly.

    1. Tighten bolts (7) to a torque of 115 N·m (85 lb ft).

  1. If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install friction shim (3) .

    1. Install friction shim (3) .

    1. Install a new front seal to the front cover. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove and Install" for the correct procedure.

  1. Install Tooling (A) to the crankshaft.



    Illustration 2g02458316

  1. Install crankshaft pulley assembly (2) onto the crankshaft.

    Note: Do not lubricate the front seal or the seal face of the crankshaft pulley assembly.

  1. Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.

  1. Remove Tooling (A) .

  1. Install remaining Torx screws (1) to crankshaft pulley assembly (2) .

  1. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1) to a torque of 40 N·m (29 lb ft).

  1. Use Tooling (B) and Tooling (C) to turn Torx screws (1) through an additional 120 degrees.

End By: Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove and Install" for the correct procedure.

Information System:

C6.6 Industrial Engine Vibration Damper and Pulley - Remove
MP15, MP20, MP30 and MP40 Multi-Processors Wear Plates - Inspect/Replace
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Inspect
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Inspect
C15 and C18 Tier 4 Final Engines Exhaust Cooler (NRS) - Test
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
C13 Tier 4 Final Engines Exhaust Cooler (NRS) - Clean
2010/05/06 Improved Remanufactured Injectors Are Now Used on Some 3408E and 3412E Machine Engines {1251, 1254, 1290, 1713}
2010/05/20 An Improved Hydraulic Tank is Available for Certain Excavators {5056}
C9.3 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
C4.4 Industrial Engine Engine Oil Pump
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C6.6 Industrial Engine Gear Group (Front) - Remove and Install
C6.6 Industrial Engine Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C6.6 Industrial Engine Idler Gear - Remove
C6.6 Industrial Engine Idler Gear - Install
C6.6 Industrial Engine Housing (Front) - Remove
C6.6 Industrial Engine Housing (Front) - Remove - Heavy Duty Housing (Front)
2010/05/13 The Gas Strut on Backhoe Loader Steering Columns Has Been Improved {4309, 4310, 4338}
C6.6 Industrial Engine Housing (Front) - Install
C6.6 Industrial Engine Housing (Front) - Install - Heavy Duty Housing (Front)