C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover Caterpillar


Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     278-2636     Front Oil Seal Removal Tool     1    

Start By:

  1. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove" for the correct procedure.


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.





    Illustration 1g02048634

  1. Position Tooling (A) on the nose of the crankshaft. Screw Tooling (A) into crankshaft front seal (2) .

    Note: Do not damage the edge of the front cover for the crankshaft front seal.

  1. Screw the bolt into Tooling (A) in order to remove crankshaft front seal (2) from front cover (1) .

Installation Procedure

Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
B     9U-6206     Stud     1    
276-1207 Locator As     1    
9U-6209 Sleeve     1    
276-1209 Seal Installer Tool     1    
9U-6207 Plate     1    


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Ensure that the bore for the crankshaft front oil seal in the front cover is clean and free from damage.



    Illustration 2g02048635

  1. Assemble Tooling (B) .

  1. Correctly position a new crankshaft front seal (2) to front cover (1) .

    Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the crankshaft front seal before installation.

  1. Use Tooling (B) to install crankshaft front seal (2) to front cover (1) . Ensure that the front face of the crankshaft front seal is installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch).

  1. Remove Tooling (B) from the crankshaft.

End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Install" for the correct procedure.

Information System:

C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Engine Oil Pump
C6.6 Industrial Engine Vibration Damper and Pulley - Install
C6.6 Industrial Engine Vibration Damper and Pulley - Remove
MP15, MP20, MP30 and MP40 Multi-Processors Wear Plates - Inspect/Replace
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Inspect
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Inspect
C15 and C18 Tier 4 Final Engines Exhaust Cooler (NRS) - Test
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
C13 Tier 4 Final Engines Exhaust Cooler (NRS) - Clean
C6.6 Industrial Engine Gear Group (Front) - Remove and Install
C6.6 Industrial Engine Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C6.6 Industrial Engine Idler Gear - Remove
C6.6 Industrial Engine Idler Gear - Install
C6.6 Industrial Engine Housing (Front) - Remove
C6.6 Industrial Engine Housing (Front) - Remove - Heavy Duty Housing (Front)
2010/05/13 The Gas Strut on Backhoe Loader Steering Columns Has Been Improved {4309, 4310, 4338}
C6.6 Industrial Engine Housing (Front) - Install
C6.6 Industrial Engine Housing (Front) - Install - Heavy Duty Housing (Front)
C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C6.6 Industrial Engine Crankcase Breather - Remove