C6.6 Industrial Engine Housing (Front) - Remove - Heavy Duty Housing (Front) Caterpillar


Housing (Front) - Remove - Heavy Duty Housing (Front)
`
1.1. Removal Procedure

Removal Procedure

Start By:

  1. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.

  2. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove" for the correct procedure.

  3. Remove the engine oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove" for the correct procedure.

  4. If the engine has an accessory drive, remove the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install" for the correct procedure.

  5. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove" for the correct procedure.

  6. Remove the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Remove and Install" for the correct procedure.

  7. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shorten component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g02198874

  1. Cut cable strap (2) from wiring harness assembly.

  2. Remove bolts (3) that secure bypass tube (1) to front housing (4).

  3. Remove bypass tube (1) from the cylinder head. Remove O-ring (5) and O-ring (6) from bypass tube (1).


    Illustration 2g02201095

  4. Remove bolts (8), bolts (9) and bolts (10) from front housing (4).

    Note: The bolts are three different lengths. Note the positions of the different length bolts.

  5. Remove front housing (4) from the cylinder block.

  6. Remove gasket (11).

  7. If necessary, follow Step 7.a through Step 7.b in order to remove bearing (7) from housing (3).

    1. Place housing (4) onto a suitable support.

    2. Use a suitable tool in order to press bearing (7) out of housing (4).


    Illustration 3g02201096

  8. Remove thrust washer (12) from the cylinder block.

Information System:

C6.6 Industrial Engine Housing (Front) - Remove
C6.6 Industrial Engine Idler Gear - Install
C6.6 Industrial Engine Idler Gear - Remove
C6.6 Industrial Engine Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C6.6 Industrial Engine Gear Group (Front) - Remove and Install
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Engine Oil Pump
C6.6 Industrial Engine Vibration Damper and Pulley - Install
C6.6 Industrial Engine Vibration Damper and Pulley - Remove
MP15, MP20, MP30 and MP40 Multi-Processors Wear Plates - Inspect/Replace
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Inspect
2010/05/13 The Gas Strut on Backhoe Loader Steering Columns Has Been Improved {4309, 4310, 4338}
C6.6 Industrial Engine Housing (Front) - Install
C6.6 Industrial Engine Housing (Front) - Install - Heavy Duty Housing (Front)
C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C6.6 Industrial Engine Crankcase Breather - Remove
C6.6 Industrial Engine Crankcase Breather - Install
C6.6 Industrial Engine Valve Mechanism Cover - Remove and Install
C13 Engines for Caterpillar Built Machines Temperature Sensor (DPF Inlet, Flame Detect)
C6.6 Industrial Engine Rocker Shaft and Pushrod - Remove
C6.6 Industrial Engine Rocker Shaft - Disassemble
MP15, MP20, MP30 and MP40 Multi-Processors Wear Tip - Inspect/Replace