C6.6 Industrial Engine Housing (Front) - Install - Heavy Duty Housing (Front) Caterpillar


Housing (Front) - Install - Heavy Duty Housing (Front)
`
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     6V-6640     Sealant     1    
B     -     Guide Bolt
M8 by 40 mm    
2    
C     319-6486     Alignment Tool     1    
- Bolts
M10 by 50 mm    
3    
D     1U-6396     O-Ring Assembly Compound     1    
E     7M-7456     Bearing Mount Compound     1    


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Ensure that the front housing is clean and free from damage. If necessary, replace the front housing.

    If necessary, install blanking plugs to a new front housing. Use Tooling (A) in order to seal all D-plugs.

  1. Clean all the gasket surfaces of the cylinder block.



    Illustration 1g02201113



    Illustration 2g02201114

  1. Inspect dowel (13) and dowel (14) for damage. If necessary, replace the dowels in the cylinder block.

  1. Install thrust washer (12) into the recess in the cylinder block. Refer to Disassembly and Assembly, "Camshaft - Install" for more information.

  1. Install Tooling (B) to the cylinder block. Refer to Illustration 2.

  1. Align a new gasket (11) with Tooling (B) . Install the gasket to the cylinder block.

    Note: Ensure that two circular Tabs (X) on the gasket are engaged in two Holes (Y) in the cylinder block. Ensure that dowel (14) in the cylinder block is engaged on the gasket.

  1. Install Tooling (C) to the cylinder block.



    Illustration 3g02201115

  1. If necessary, follow Step 8.a through Step 8.c in order to install bearing (7) to housing (4) .

    1. Apply a small continuous bead of Tooling (E) to outer Surface (Z) of bearing (7) .

    1. Place housing (4) onto a suitable support.

    1. Use a suitable tool in order to press bearing (7) into housing (3) until the bearing is in the correct position within the housing. Remove any excess bearing mount compound.

  1. Install the front housing over Tooling (B) and Tooling (C) onto the cylinder block.



    Illustration 4g02201116

    (8) M8 by 20 mm

    (9) M8 by 35 mm

    (10) M8 by 25 mm

  1. Install new bolts (10) to front housing (3) hand tight.

  1. Remove Tooling (B) .

  1. Loosely install bolts (8) and bolts (9) finger tight. Refer to Illustration 4 for the correct position of the bolts.



    Illustration 5g02058297

  1. Tighten bolts (8) , bolts (9) and bolts (10) in the sequence that is shown in Illustration 5 to a torque of 28 N·m (248 lb in).

  1. Remove Tooling (C) from the cylinder block.



    Illustration 6g02198874

  1. Install new O-ring seal (5) and O-ring seal (6) to bypass tube (1) . Use Tooling (D) in order to lubricate the O-ring seals.

  1. Install bypass tube (1) to the cylinder head. Install bolts (3) . Tighten the bolts to a torque of 9 N·m (80 lb in).

  1. Install a new cable strap (2) to wiring harness assembly.

End By:

  1. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install" for the correct procedure.
  2. Install the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Install" for the correct procedure.
  3. If the engine has an accessory drive, install the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
  4. Install the engine oil pan plate . Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove" for the correct procedure.
  5. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Install" for the correct procedure.
  6. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install" for the correct procedure.
  7. Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.
  8. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Fill" for the correct procedure.

Information System:

C6.6 Industrial Engine Housing (Front) - Install
2010/05/13 The Gas Strut on Backhoe Loader Steering Columns Has Been Improved {4309, 4310, 4338}
C6.6 Industrial Engine Housing (Front) - Remove - Heavy Duty Housing (Front)
C6.6 Industrial Engine Housing (Front) - Remove
C6.6 Industrial Engine Idler Gear - Install
C6.6 Industrial Engine Idler Gear - Remove
C6.6 Industrial Engine Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C6.6 Industrial Engine Gear Group (Front) - Remove and Install
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Engine Oil Pump
C6.6 Industrial Engine Vibration Damper and Pulley - Install
C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C6.6 Industrial Engine Crankcase Breather - Remove
C6.6 Industrial Engine Crankcase Breather - Install
C6.6 Industrial Engine Valve Mechanism Cover - Remove and Install
C13 Engines for Caterpillar Built Machines Temperature Sensor (DPF Inlet, Flame Detect)
C6.6 Industrial Engine Rocker Shaft and Pushrod - Remove
C6.6 Industrial Engine Rocker Shaft - Disassemble
MP15, MP20, MP30 and MP40 Multi-Processors Wear Tip - Inspect/Replace
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems Pilot Valve (Travel) - Disassemble
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems Pilot Valve (Travel) - Assemble
Removing the 2W-1055 Elbow {1307}