C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "B" Caterpillar


Accessory Drive - Remove and Install - Accessory Drive SAE "B"
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
8H-0663  Bearing Puller  
5F-7345 Puller 
126-7183 Crossblock 
126-7177 Puller Leg 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Dispose of all fluids according to local regulations and mandates.


  1. Remove the auxiliary equipment from the accessory drive housing. Refer to the Original Equipment Manufactures (OEM) for the correct procedure.


    Illustration 1g02186453


    Illustration 2g02374996

  2. If the OEM driven equipment has not been installed to the auxiliary drive, remove bolts (1). Remove cover plate (2) and remove gasket (3) (not shown).

  3. Remove Allen head screws (4) from accessory drive housing (5). Remove Allen head screw (6) from accessory drive housing (5).

  4. Remove accessory drive housing (5) from the front housing.

  5. Remove gasket (7) from accessory drive housing (5).


    Illustration 3g02374997

  6. If necessary, follow Step 6.a through Step 6.d in order to disassemble the accessory drive.

    1. Remove circlip (11) from gear (9).

    2. Remove circlip (12) from accessory drive housing (5).

    3. Place accessory drive housing (5) onto a suitable support. Press the assembly of gear (9) and bearing (10) out of accessory drive housing (5). Use Tooling (A) in order to remove bearing (10) from gear (9).

      Note: Note the position of the bearing in the accessory drive housing before removal.

    4. Press bearing (8) out of accessory drive housing (5).

Installation Procedure

Table 2
Required Tools 
Tool  Part Number  Part Description  Qty 
7M-7456  Bearing Mount Compound 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 4g02374997


    Illustration 5g02052174


    Illustration 6g02052273

  1. If necessary, follow Step 1.a through Step 1.f in order to assemble the accessory drive.

    1. Inspect the condition of the teeth and the splines of gear (9) for wear and damage. Inspect bearing (8), bearing (10), circlip (11) and circlip (12). Inspect the front housing for wear and damage. Replace any components that are worn or damaged.

    2. Apply a small continuous bead of Tooling (B) to outer Surface (X) of bearing (8). Place the accessory drive housing on a suitable support. Press on the outer race of bearing (8) until the bearing is in the correct position within accessory drive housing (5). Remove any excess bearing mount compound.

    3. Apply a small continuous bead of Tooling (B) to inner Surface (Y) of bearing (10). Place the inner race of bearing (10) onto a suitable support. Press the shaft of gear (9) into bearing (10) until the shoulder of the gear is against the bearing. Remove any excess bearing mount compound.

    4. Install circlip (11) into the groove in gear (9).

    5. Apply a small continuous bead of Tooling (B) to the outer Surface (Z) of bearing (10). Place accessory drive housing (5) on a suitable support. Ensure that the shaft of gear (9) is correctly aligned with bearing (8). Press the assembly of the gear into the accessory drive housing. Remove any excess bearing mount compound.

    6. Install circlip (12) into the groove in accessory drive housing (5). Ensure that circlip (12) is correctly positioned in the groove.

  2. Inspect the bore in the front housing for damage. If necessary, replace the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" and Disassembly and Assembly, "Housing (Front) - Install" for the correct procedure.

  3. Lightly lubricate bearing (8), bearing (10), and gear (9) with clean engine oil.


    Illustration 7g02374996

  4. Install new gasket (7) to accessory drive assembly (5). Install the assembly of the accessory drive to the front housing.

  5. Install new M8 Allen head screws (4) to accessory drive housing (5).

  6. Install a new M12 Allen head screw (6) to accessory drive housing (5).

  7. Tighten new M8 Allen head screws (4) to a torque of 22 N·m (195 lb in).

  8. Tighten M12 Allen head screw (6) to a torque of 78 N·m (58 lb ft).

  9. Repeat Step 7 to ensure correct torque of M8 Allen head screws (4).

  10. Ensure that there is tactile backlash between the idler gear and the accessory drive gear.

  11. Install the auxiliary equipment to the accessory drive housing. Refer to the OEM for the correct procedure.


    Illustration 8g02186453

  12. If the OEM driven equipment is not being installed to the auxiliary drive. Install a new gasket (3) (not shown) and cover plate (2). Install bolts (1) and tighten the bolts to a torque of 44 N·m (33 lb ft).

Information System:

C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C6.6 Industrial Engine Housing (Front) - Install - Heavy Duty Housing (Front)
C6.6 Industrial Engine Housing (Front) - Install
2010/05/13 The Gas Strut on Backhoe Loader Steering Columns Has Been Improved {4309, 4310, 4338}
C6.6 Industrial Engine Housing (Front) - Remove - Heavy Duty Housing (Front)
C6.6 Industrial Engine Housing (Front) - Remove
C6.6 Industrial Engine Idler Gear - Install
C6.6 Industrial Engine Idler Gear - Remove
C6.6 Industrial Engine Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C6.6 Industrial Engine Gear Group (Front) - Remove and Install
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install
C6.6 Industrial Engine Crankcase Breather - Remove
C6.6 Industrial Engine Crankcase Breather - Install
C6.6 Industrial Engine Valve Mechanism Cover - Remove and Install
C13 Engines for Caterpillar Built Machines Temperature Sensor (DPF Inlet, Flame Detect)
C6.6 Industrial Engine Rocker Shaft and Pushrod - Remove
C6.6 Industrial Engine Rocker Shaft - Disassemble
MP15, MP20, MP30 and MP40 Multi-Processors Wear Tip - Inspect/Replace
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems Pilot Valve (Travel) - Disassemble
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems Pilot Valve (Travel) - Assemble
Removing the 2W-1055 Elbow {1307}
349E Excavator Hydraulic System Specifications
C15 and C18 Engines for Caterpillar Built Machines Exhaust Elbow - Remove and Install