C6.6 Industrial Engine Valve Mechanism Cover - Remove and Install Caterpillar


Valve Mechanism Cover - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Start By:

  1. Remove the inlet air control (NRS Induction Mixer). Refer to Disassembly and Assembly, "Inlet Air Control (NRS Induction Mixer) - Remove" for the correct procedure.


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g02438036

  1. Disconnect plastic tube assembly (2) from the crankcase breather on valve mechanism cover (7). Refer to Disassembly and Assembly, "Crankcase Breather - Remove" for the correct procedure.

  2. Remove bolt (3) from clip for tube assembly (4).

  3. Remove bolt (5) from clip for tube assembly (6).

  4. Remove bolt (8) and position pressure sensor manifold (1) away from valve mechanism cover (7).

  5. Remove bolts (9) from valve mechanism cover (7).

  6. Remove valve mechanism cover (7) from the cylinder head.

    Note: Remove the valve mechanism cover vertically in order to avoid damage to the electronic unit injectors.



    Illustration 2g02173457

  7. Remove gasket (10) from valve mechanism cover (7).

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 3g02173457

  1. Thoroughly clean all gasket surfaces of valve mechanism cover (7). Clean the gasket surfaces of the cylinder head.

  2. Inspect gasket (10) for damage. If necessary, install a new gasket to valve mechanism cover (7).

    Note: Ensure that the gasket is fully seated into the groove of the valve mechanism cover.



    Illustration 4g02173458


    Illustration 5g02438036


    Illustration 6g02002834

  3. Ensure that harness assemblies (12) are not in contact with rocker arms (11) or cylinder head (13).

    Note: Install the valve mechanism cover vertically in order to avoid damage to the electronic unit injectors.

  4. Position valve mechanism cover (7) onto cylinder head (13). Ensure that harness assemblies (12) are not trapped during the assembly procedure.

  5. Install bolts (9).

  6. Tighten bolts (9) in the numerical sequence that is shown in Illustration 6. Tighten the bolts to a torque of 9 N·m (79 lb in).

    Repeat Step 6 in order to ensure correct torque.

  7. Position pressure sensor manifold (1) onto inlet elbow. Loosely install bolt (8).

  8. Install bolt (3) to clip for tube assembly (4).

  9. Install bolt (5) to clip for tube assembly (6).

  10. Tighten bolt (8) to a torque of 22 N·m (195 lb in).

  11. Tighten bolt (3) and bolt (5) to a torque of 22 N·m (195 lb in).

  12. Connect plastic tube assembly (2) to the crankcase breather on valve mechanism cover (7). Refer to Disassembly and Assembly, "Crankcase Breather - Remove" for the correct procedure.

End By:

  1. Install the inlet air control (NRS Induction Mixer). Refer to Disassembly and Assembly, "Inlet Air Control (NRS Induction Mixer) - Install" for the correct procedure.

Information System:

C6.6 Industrial Engine Crankcase Breather - Install
C6.6 Industrial Engine Crankcase Breather - Remove
C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C6.6 Industrial Engine Housing (Front) - Install - Heavy Duty Housing (Front)
C6.6 Industrial Engine Housing (Front) - Install
2010/05/13 The Gas Strut on Backhoe Loader Steering Columns Has Been Improved {4309, 4310, 4338}
C6.6 Industrial Engine Housing (Front) - Remove - Heavy Duty Housing (Front)
C6.6 Industrial Engine Housing (Front) - Remove
C6.6 Industrial Engine Idler Gear - Install
C6.6 Industrial Engine Idler Gear - Remove
C6.6 Industrial Engine Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C13 Engines for Caterpillar Built Machines Temperature Sensor (DPF Inlet, Flame Detect)
C6.6 Industrial Engine Rocker Shaft and Pushrod - Remove
C6.6 Industrial Engine Rocker Shaft - Disassemble
MP15, MP20, MP30 and MP40 Multi-Processors Wear Tip - Inspect/Replace
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems Pilot Valve (Travel) - Disassemble
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems Pilot Valve (Travel) - Assemble
Removing the 2W-1055 Elbow {1307}
349E Excavator Hydraulic System Specifications
C15 and C18 Engines for Caterpillar Built Machines Exhaust Elbow - Remove and Install
324E Excavator Declaration of Conformity
C9.3 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C6.6 Industrial Engine Rocker Shaft - Assemble