C6.6 Industrial Engine Rocker Shaft and Pushrod - Remove Caterpillar


Rocker Shaft and Pushrod - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
A(1)  9U-6198  Crankshaft Turning Tool 
A(2)  5P-7306  Housing 
5P-7305 Engine Turning Tool 
367-8608  Engine Timing Pin 
298-5564  T40 Torx Socket 
227-4389  E10 Torx Socket 
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.

Start By:

  1. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.

Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01992076

  1. Remove plug (2) from the cylinder block. Remove O-ring seal (1) from the plug.

  2. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Position the Valve Mechanism Before Maintenance Procedures" for the correct procedure. Install Tooling (B) through Hole (W) in order to lock the crankshaft.

  3. Remove Tooling (B).

  4. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the crankshaft at 60 degrees after top dead center.


    Illustration 2g01992077

  5. Use Tooling (C) in order to loosen threaded inserts (4) on all rocker arms (3). Unscrew threaded inserts (4) on all rocker arms (3) until all valves are fully closed. Ensure that guides (5) for the pushrods are left in position on threaded inserts (4).

    Note: Ensure that ALL threaded inserts are fully unscrewed.



    Illustration 3g02003036


    Illustration 4g02003035

  6. Use Tooling (D) to loosen Torx screws (7). Begin at the ends of rocker shaft assembly (2) and work toward the center.

    Note: To avoid distortion of the rocker shaft assembly, each Torx screw should be loosened by half a turn at one time. Repeat the procedure until all Torx screws are loosened.

  7. Remove Torx screws (7) from rocker shaft assembly (8).

    Note: Note Position (X) of different length Torx screws (7).

  8. Remove rocker shaft assembly (8) from the cylinder head.

  9. Place an identification mark on pushrods (9) in order to show the location. Remove the pushrods from the cylinder head.

    Note: Identification will ensure that the pushrods can be reinstalled in the original positions. Do not interchange the positions of used pushrods.

  10. Make a temporary mark on valve bridges (6) in order to show the location and the orientation. Remove the valve bridges from the cylinder head.

    Note: Identification will ensure that the valve bridges can be reinstalled in the original location and the original orientation. Do not interchange the location or the orientation of used valve bridges.

Information System:

C13 Engines for Caterpillar Built Machines Temperature Sensor (DPF Inlet, Flame Detect)
C6.6 Industrial Engine Valve Mechanism Cover - Remove and Install
C6.6 Industrial Engine Crankcase Breather - Install
C6.6 Industrial Engine Crankcase Breather - Remove
C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C6.6 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C6.6 Industrial Engine Housing (Front) - Install - Heavy Duty Housing (Front)
C6.6 Industrial Engine Housing (Front) - Install
2010/05/13 The Gas Strut on Backhoe Loader Steering Columns Has Been Improved {4309, 4310, 4338}
C6.6 Industrial Engine Housing (Front) - Remove - Heavy Duty Housing (Front)
C6.6 Industrial Engine Housing (Front) - Remove
C6.6 Industrial Engine Idler Gear - Install
C6.6 Industrial Engine Rocker Shaft - Disassemble
MP15, MP20, MP30 and MP40 Multi-Processors Wear Tip - Inspect/Replace
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems Pilot Valve (Travel) - Disassemble
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems Pilot Valve (Travel) - Assemble
Removing the 2W-1055 Elbow {1307}
349E Excavator Hydraulic System Specifications
C15 and C18 Engines for Caterpillar Built Machines Exhaust Elbow - Remove and Install
324E Excavator Declaration of Conformity
C9.3 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C6.6 Industrial Engine Rocker Shaft - Assemble
C6.6 Industrial Engine Rocker Shaft and Pushrod - Install
C6.6 Industrial Engine Cylinder Head - Remove