Engine Oil Pressure Sensor - Remove and Install
`
C6.6 Industrial Engine
[KENR9110]
C6.6 Industrial Engine
Coolant Temperature Sensor - Remove and Install
C6.6 Industrial Engine
Soot Antenna - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
- Slide locking tab (1) into the unlocked position. Disconnect harness assembly (3) from engine oil pressure sensor (4).
- Use a deep socket to remove engine oil pressure sensor (4) from the cylinder block.
- Remove O-ring seal (2) from engine oil pressure sensor (4).
Show/hide table
| |
| Illustration 1 | g02024355 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install a new O-ring seal (2) onto engine oil pressure sensor (4).
Note: Do not lubricate the O-ring seal.
- Use a deep socket to install engine oil pressure sensor (4) to the cylinder block. Tighten the engine oil pressure sensor to a torque of
10 N·m (89 lb in) . - Connect harness assembly (3) to engine oil pressure sensor (4).
- Slide locking tab (1) into the locked position.
- If necessary, fill the engine oil pan to the correct level that is indicated on the engine oil level gauge. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check".
Show/hide table
|
| |
| Illustration 2 | g02024355 |
Information System:
C6.6 Industrial Engine
Coolant Temperature Sensor - Remove and Install
C6.6 Industrial Engine
Crankshaft Position Sensor - Remove and Install
C6.6 Industrial Engine
Camshaft Position Sensor - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Joystick Control - Calibrate
336D MHPU Mobile Hydraulic Power Unit Hydraulic System
Combined Function Hydraulic System - System 18
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
System Pressure - Release
C4.4 Industrial Engine
Alternator
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Boom Bearings and Seals - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Boom - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Boom Cylinder - Remove and Install
C9.3 Engines for Caterpillar Built Machines
Rocker Arm and Shaft - Remove
C6.6 Industrial Engine
Atmospheric Pressure Sensor - Remove and Install
C6.6 Industrial Engine
Soot Antenna - Remove and Install
C6.6 Industrial Engine
Temperature Sensor (DPF) - Remove and Install
C6.6 Industrial Engine
Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C6.6 Industrial Engine
Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - NRS Inlet and Outlet Pressure Sensors
C6.6 Industrial Engine
Boost Pressure Sensor - Remove and Install
C6.6 Industrial Engine
Inlet Manifold Temperature Sensor - Remove and Install
C6.6 Industrial Engine
Glow Plugs - Remove and Install
C6.6 Industrial Engine
Alternator Belt - Remove and Install
C6.6 Industrial Engine
Idler Pulley - Remove and Install - Grooved Idler Pulley
C6.6 Industrial Engine
Idler Pulley - Remove and Install - Flat Idler Pulley
C6.6 Industrial Engine
Belt Tensioner - Remove and Install
C6.6 Industrial Engine
Fan - Remove and Install