Hydraulic Lockout Control - Remove and Install
`
349F and 352F Excavators Machine Systems
[UENR0194]
349F and 352F Excavators Machine Systems
Duo-Cone Conventional Seals - Install
349F and 352F Excavators Machine Systems
Pilot Valve (Joystick) - Disassemble
OPERATOR STATION
CONTROL GP-HYDRAULIC
349F and 352F Excavators Machine Systems
Pilot Valve (Travel) - Disassemble
349F and 352F Excavators Machine Systems
Pilot Valve (Travel) - Assemble
349F and 352F Excavators Machine Systems
Hydraulic Lockout Control - Remove and Install
349F and 352F Excavators Machine Systems
Pilot Valve (Travel) - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Loctite 243 | - |
- Remove covers (1), (2), and (3).
Show/hide table
Illustration 2 g02153847 - Disconnect harness assembly (4).
- Remove bolts (6) and hydraulic lockout control (5).
Show/hide table
Illustration 3 g02153899 - Remove screws (8) and knob (7).
- Remove screws (9) and limit switch (10).
Show/hide table
| |
| Illustration 1 | g02153846 |
- Install hydraulic lockout control (5) in the reverse order of removal.
- Apply Tooling (A) to the threads of screws (9). Tighten screws (9) to a torque of
0.7 ± 0.1 N·m (6.1 ± 0.9 lb in) . - Apply Tooling (A) to the threads of screws (8). Tighten screws (8) to a torque of
1.5 ± 0.2 N·m (13.2 ± 1.8 lb in) .
- Apply Tooling (A) to the threads of screws (9). Tighten screws (9) to a torque of
Information System:
330F MHPU Mobile Hydraulic Power Unit
Engine Oil Level - Check
Installation Procedure for 275-7203 Auxiliary Control Wiring Gp {1408}
320E and 323E Excavators
Cooling System Coolant Level - Check
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems
Final Drive - Assemble - Type-Two
320E and 323E Excavators
Cooling System Coolant Extender (ELC) - Add
320D Excavator
Fuel System Fourth Filter - Replace - If Equipped
324E Excavator
Cooling System Coolant (ELC) - Change
2010/05/28
VIMS<SUP>TM</SUP> Supervisor January 2010 is Now Available {7601}
C4.4 Industrial Engine
Turbocharger - Single Turbocharger
C4.4 Industrial Engine
Exhaust Gas Valve (NRS)
MP15, MP20, MP30 and MP40 Multi-Processors
Jaw - Repair
Installation Procedure for the 360-6814 Hydraulic Kit (Center Lock Conversion){5057}
C9.3 Engines for Caterpillar Built Machines
Electrical Connectors
C6.6 Industrial Engine
Vibration Damper - Check
324E Excavator
Engine Oil and Filter - Change
Installation Procedure for the 260-8013 Front Lines Group {5057}
Reuse Guideline for the Flexible Exhaust Pipe Group on Tier 4 Engines {1061}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Fuel Tank - Remove and Install
349F and 352F Excavators Machine Systems
Pilot Valve (Joystick) - Disassemble
349F and 352F Excavators Machine Systems
Pilot Valve (Joystick) - Assemble
325 VM and VH Variable Gauge Undercarriage
Track Roller - Remove and Install
325 VM and VH Variable Gauge Undercarriage
Sprocket - Remove and Install
Reuse and Salvage for Flywheel Assemblies {0679, 1156}
C7.1 Industrial Engine
Air Control Valve - Remove and Install - Clean Emissions Module