Engine Oil Filter Base - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1U-8760 | Chain Wrench | 1 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
- Place a suitable container below engine oil filter (5) in order to catch any oil that might be spilled.
- Use Tooling (A) to remove engine oil filter (5). Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
- Remove bolts (3).
Note: If bolts of different lengths are installed, identify the correct position of the bolts.
- Remove engine oil filter base (4).
- Remove gasket (6).
- If necessary, remove plug (1) from engine oil filter base (4). Remove O-ring seal (2) from plug (1).
Show/hide table
| |
| Illustration 1 | g01980935 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean engine oil filter base (4). Clean the gasket surfaces of the cylinder block or the engine oil cooler.
- If necessary, install new O-ring seal (2) to plug (1). Install plugs (1) to engine oil filter base (4). Tighten the plug to a torque of
12 N·m (106 lb in) . - Install bolts (3) to engine oil filter base (4).
- Install a gasket (6) onto bolts (3). Install the assembly of the engine oil filter base to the cylinder block or the engine oil cooler.
- Tighten bolts (3) to a torque of
22 N·m (195 lb in) . - Install a new engine oil filter (5) and check the level of the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure.
Show/hide table
|
| |
| Illustration 2 | g01980935 |
Information System:
C7.1 Industrial Engine
Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Industrial Engine
Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Industrial Engine
Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Industrial Engine
Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Industrial Engine
Electronic Unit Injector - Remove
C7.1 Industrial Engine
Electronic Unit Injector - Install
C7.1 Industrial Engine
Electronic Control Module - Remove and Install - Electronic Control Module With Banjo Bolt Connections
C7.1 Industrial Engine
Electronic Control Module - Remove and Install - Electronic Control Module With Quick Coupler Connections
C7.1 Industrial Engine
Electric Starting Motor - Remove and Install
C7.1 Industrial Engine
ECM Mounting Bracket - Remove and Install
C7.1 Industrial Engine
Diesel Particulate Filter - Remove
C7.1 Industrial Engine
Diesel Particulate Filter - Install
C7.1 Industrial Engine
Engine Oil Filter Base - Remove and Install - Engine Oil Filter Base with Adapter
C7.1 Industrial Engine
Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Industrial Engine
Engine Oil Pan - Remove - Aluminum Oil Pan
C7.1 Industrial Engine
Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C7.1 Industrial Engine
Engine Oil Pressure Sensor - Remove and Install
C7.1 Industrial Engine
Engine Oil Pump - Install
C7.1 Industrial Engine
Engine Oil Pump - Remove
C7.1 Industrial Engine
Exhaust Cooler (NRS) - Remove and Install
C7.1 Industrial Engine
Exhaust Manifold - Remove and Install
C7.1 Industrial Engine
Fan - Remove and Install
C7.1 Industrial Engine
Fan Drive - Remove and Install
C7.1 Industrial Engine
Flame Detection Temperature Sensor - Remove and Install - Flame Detection Temperature Sensor for the ARD