Engine Oil Filter Base - Remove and Install - Engine Oil Filter Base with Adapter
`
C7.1 Industrial Engine
[KENR9105]
C7.1 Industrial Engine
Engine Oil Filter Base - Remove and Install
C7.1 Industrial Engine
Engine Oil Pan - Install - Aluminum Oil Pan
1.1. Removal Procedure
2.1. Installation Procedure
Start By:
- Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter Base - Removal and Install" for the correct procedure.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (1), bolts (2) and bolts (3).
Note: Note the position of the bolts and the length of the bolts.
Show/hide table
Illustration 2 g02047397 Typical example - Remove adapter (6) and spacer (5) from the cylinder block. Remove gasket (4) and gasket (8).
- If necessary, remove split collars (7) from adapter (6).
Show/hide table
| |
| Illustration 1 | g02047393 |
|
Typical example | |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean the gasket surfaces of the adapter. Clean the gasket surfaces of the cylinder block.
Show/hide table
Illustration 3 g02047397 Typical example Show/hide table
Illustration 4 g02047393 Typical example - Position new gasket (4) and gasket (8) onto adapter (6).
- If necessary, install split collars (7) to adapter (6).
- Install bolts (1), bolts (2) and bolts (3) to adapter (6). Install spacer (5) to applicable bolt (2).
- Position adapter (6) to the cylinder block.
Show/hide table
Illustration 5 g02047413 - Tighten bolts (1) and bolts (2) to a torque of
22 N·m (195 lb in) . Tighten the bolts in the sequence that is shown in Illustration 5.Tighten bolts (3) in Position (X) to a torque of
44 N·m (32 lb ft) . Tighten the bolts in the sequence that is shown in Illustration 5. - Install the oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter Base - Removal and Install" for the correct procedure.
Information System:
C7.1 Industrial Engine
Engine Oil Filter Base - Remove and Install
C7.1 Industrial Engine
Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Industrial Engine
Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Industrial Engine
Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Industrial Engine
Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Industrial Engine
Electronic Unit Injector - Remove
C7.1 Industrial Engine
Electronic Unit Injector - Install
C7.1 Industrial Engine
Electronic Control Module - Remove and Install - Electronic Control Module With Banjo Bolt Connections
C7.1 Industrial Engine
Electronic Control Module - Remove and Install - Electronic Control Module With Quick Coupler Connections
C7.1 Industrial Engine
Electric Starting Motor - Remove and Install
C7.1 Industrial Engine
ECM Mounting Bracket - Remove and Install
C7.1 Industrial Engine
Diesel Particulate Filter - Remove
C7.1 Industrial Engine
Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Industrial Engine
Engine Oil Pan - Remove - Aluminum Oil Pan
C7.1 Industrial Engine
Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C7.1 Industrial Engine
Engine Oil Pressure Sensor - Remove and Install
C7.1 Industrial Engine
Engine Oil Pump - Install
C7.1 Industrial Engine
Engine Oil Pump - Remove
C7.1 Industrial Engine
Exhaust Cooler (NRS) - Remove and Install
C7.1 Industrial Engine
Exhaust Manifold - Remove and Install
C7.1 Industrial Engine
Fan - Remove and Install
C7.1 Industrial Engine
Fan Drive - Remove and Install
C7.1 Industrial Engine
Flame Detection Temperature Sensor - Remove and Install - Flame Detection Temperature Sensor for the ARD
C7.1 Industrial Engine
Flywheel - Install - Equipped with Rear Power Take-Off