Water Pump - Remove
`
C7.1 Industrial Engine
[KENR9105]
C7.1 Industrial Engine
Water Pump - Install
C7.1 Industrial Engine
Water Temperature Regulator - Remove and Install
1.1. Removal Procedure
Start By:
- Remove the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
- Loosen the hose clamps and remove the hose from the water pump inlet.
Show/hide table
Illustration 1 g02164768 - Remove bolts (4).
- Remove water pump (3) from front cover (1).
Note: If necessary, tap the water pump with a soft faced hammer in order to loosen the water pump.
- Remove gasket (2).
Information System:
C7.1 Industrial Engine
Water Pump - Install
C7.1 Industrial Engine
Wastegate Solenoid - Remove and Install
C7.1 Industrial Engine
Vibration Damper and Pulley - Remove
C7.1 Industrial Engine
Vibration Damper and Pulley - Install
C7.1 Industrial Engine
Valve Mechanism Cover - Remove and Install
C7.1 Industrial Engine
Turbocharger - Remove - Second Stage Turbocharger
C7.1 Industrial Engine
Turbocharger - Install - Second Stage Turbocharger
C7.1 Industrial Engine
Turbocharger - Remove - First Stage Turbocharger
C7.1 Industrial Engine
Turbocharger - Install - First Stage Turbocharger
C7.1 Industrial Engine
Throttle Valve (Intake Air) - Remove
C7.1 Industrial Engine
Throttle Valve (Intake Air) - Install
C7.1 Industrial Engine
Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C7.1 Industrial Engine
Water Temperature Regulator - Remove and Install
C7.1 Industrial Engine
Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
Cleaning Procedure After a Pump, Motor, or Cylinder Failure for Backhoe Loaders{5050, 7000}
Installation of the 267-8004 Auxiliary Control Wiring Gp {1408}
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
System Pressure - Release
2010/07/12
A New Water Separator Gp Is Used on Certain Mini Hydraulic Excavators {1261, 1274}
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Accumulator (Hydraulic Pilot) - Remove and Install
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Cab - Remove
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Cab - Install
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Swivel - Remove
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Swivel - Install
349F and 352F Excavators Machine System
Pilot Valve (Swing Parking Brake)